Bedienungsanleitung President Taylor II Classic (Seite 26 von 44) (Deutsch, Englisch, Französisch, Spanisch)

636647

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

OUTPUT RADIUS PATTERNS

2) ANTENNA INSTALLATION

a) Choosing your antenna

- For CB radios, the longer the antenna, the better its results. Your dealer will

be able to help you with your choice of antenna.

b) Mobile antenna

- Must be fixed to the vehicle where there is a maximum of metallic surface

(ground plane), away from windscreen mountings.

- If you already have a radio-telephone antenna installed, the CB antenna

should be higher than this.

- There are two types of antenna: pre-regulated which should be used on a

good ground plane (e.g. car roof or lid of the boot), and

. adjustable which offer a much larger range and can be used on a smaller

ground plane (see p 27 § 5, Adjustment of SWR).

- For an antenna which must be fixed by drilling, you will need a good contact

between the antenna and the ground plane. To obtain this, you should lightly

scratch the surface where the screw and tightening star are to be placed.

- Be careful not to pinch or flatten the coaxial cable (as this runs the risk of break

down and/or short circuiting).

- Connect the antenna (B).

c) Fixed antenna

- A fixed antenna should be installed in a clear a space as possible. If it is fixed

to a mast, it will perhaps be necessary to stay it, according to the laws in force

(you should seek professional advice). All PRESIDENT antennas and accesso-

ries are designed to give maximum efficiency to each CB radio within the

range.

3) POWER CONNECTION

Your PRESIDENT TAYLOR II Classic is protected against an inversion of polarities.

However, before switching it on, you are advised to check all the connec-

tions. Your equipment must be supplied with a continued current of 12 volts

(A). Today, most cars and lorries are negative earth. You can check this by

making sure that the negative terminal of the battery is connected either to

the engine block or to the chassis. If this is not the case, you should consult your

dealer.

WARNING: Lorries generally have two batteries and an electrical installation

of 24 volts, in which case it will be necessary to insert a 24/12 volt converter

(type CV 24/12 PRESIDENT) into the electrical circuit. The following connection

steps should be carried out with the power cable disconnected from the set.

a) Check that the battery is of 12 volts.

b) Locate the positive and negative terminals of the battery (+ is red and - is

black). Should it be necessary to lengthen the power cable, you should use

the same or a superior type of cable.

c) It is necessary to connect your CB to a permanent (+) and (-). We advise you

to connect the power cable directly to the battery (as the connection of the

CB cable to the wiring of the car-radio or other parts of the electrical circuit

may, in somecases, increase the likelihood of interference).

d) Connect the red wire (+) to the positive terminal of the battery and the black

(-) wire to the negative terminal of the battery.

e) Connect the power cable to your CB radio.

WARNING: Never replace the original fuse (2 A) by one of a different value.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

President Taylor II Classic Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info