Bedienungsanleitung President Tommy (Seite 30 von 52) (Englisch, Französisch, Spanisch, Polnisch)

636652

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

OUTPUT RADIUS PATTERN

2) ANTENNA INSTALLATION

a) Choosing your antenna:

- For CB radios, the longer the antenna, the better its results. Your dealer will be able

to help you with your choice of antenna.

b) Mobile antenna:

- Must be ﬁxed to the vehicle where there is a maximum of metallic surface (ground

plane), away from windscreen mountings.

- If you already have a radio-telephone antenna installed, the CB antenna should be

higher than this.

- There are two types of antenna: pre-regulated which should be used on a good

ground plane (e.g. car roof or lid of the boot), and adjustable which offer a much

larger range and can be used on a smaller ground plane (see § 5, Adjustment of

SWR).

- For an antenna which must be ﬁxed by drilling, you will need a good contact be-

tween the antenna and the ground plane. To obtain this, you should lightly scratch

the surface where the screw and tightening star are to be placed.

- Be careful not to pinch or ﬂatten the coaxial cable (as this runs the risk of break down

and/or short-circuiting).

- Connect the antenna (B).

c) Fixed antenna:

- A ﬁxed antenna should be installed in a clear a space as possible. If it is ﬁxed to a

mast, it will perhaps be necessary to stay it, according to the laws in force (you should

seek professional advice). All PRESIDENT

antennas and accessories are designed

to give maximum efﬁciency to each CB

radio within the range.

3) POWER CONNECTION

Your PRESIDENT TOMMY ASC is protected against an inversion of polarities. However,

before switching it on, you are advised to check all the connections. Your equipment

must be supplied with a continued current of 12 volts (A). Today, most cars and lorries

are negative earth. You can check this by making sure that the negative terminal

of the battery is connected either to the engine block or to the chassis. If this is not

the case, you should consult your dealer.

WARNING: Lorries generally have two batteries and an electrical installation of 24

volts, in which case it will be necessary to insert a 24/12 volt converter (type CV 24/12

PRESIDENT) into the electrical circuit. The following connection steps should be carried

out with the power cable disconnected from the set.

a) Check that the battery is of 12 volts.

b) Locate the positive and negative terminals of the battery (+ is red and - is black).

Should it be necessary to lengthen the power cable, you should use the same or a

superior type of cable.

c) It is necessary to connect your CB to a permanent (+) and (-). We advise you to con-

nect the power cable directly to the battery (as the connection of the CB cable to

the wiring of the car-radio or other parts of the electrical circuit may, in some cases,

increase the likelihood of interference).

d) Connect the red wire (+) to the positive terminal of the battery and the black (-)

wire to the negative terminal of

the battery.

e) Connect the power cable to your

CB radio.

WARNING: Never replace the

original fuse (2 A) by one of a

different value.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

President Tommy Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info