Bedienungsanleitung Pride Colt Series (Seite 40 von 48) (Englisch)

722008

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

www.pridemobility.com Colt Series

Follow these easy steps for a quick and safe repair

for solid tyres:

1. Remove the key from the key switch.

2. Elevate the side of the scooter of which you are

removing the tyre. Place wooden blocks under the

frame to elevate the scooter.

3. Remove the wheel cap, drive wheel nut and

washer from the axle. See figure 29.

4. Pull the wheel off of the axle.

5. Slide the new wheel onto the axle. Make sure the

the axle key is in the axle slot.

WARNING! Failure to ensure that the

axle key is properly installed into the

axle slot when mounting the wheel can

result in electronic brake failure,

personal injury and/or product damage.

6. Reinstall the drive wheel nut and washer onto the axle and tighten.

WARNING! Make sure that both the nut and washer are reinstalled and tightened

properly.

7. Reinstall the wheel cap.

8. Remove the blocks from beneath the scooter.

IX. CARE AND MAINTENANCE

Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your

ability to perform the maintenance listed below, you may schedule inspection and maintenance at your

authorised Pride Dealer. The following areas require periodic inspection and/or care and maintenance.

TYRE PRESSURE

 If equipped with pneumatic tyres, always maintain the psi/bar/kPa air pressure rating indicated on

each tyre.

WARNING! It is important that the psi/bar/kPa air pressure rating indicated on each tyre

be maintained in pneumatic tyres at all times. Do not underinflate or overinflate your

tyres. Low pressure may result in loss of control and overinflated tyres may burst. Failure

to maintain the psi/bar/kPa air pressure rating indicated on the tyres at all times may

result in tyre and/or wheel failure.

 Regularly inspect your scooter’s tyres for signs of wear.

WHEEL REPLACEMENT

If your scooter is equipped with pneumatic tyres and you have a flat tyre, you can have the tube replaced. If your

scooter is equipped with a solid tyre insert, either the solid insert or the entire wheel must be replaced depending

on the model. Contact your authorised Pride Dealer for information regarding replacement wheels for your scooter.

WARNING! Be sure that the key is removed from the key switch and the scooter is not in

freewheel mode before performing this procedure repair.

WARNING! Completely deflate pneumatic tyres before dismantling the wheel or attempting

repair.

WARNING! When changing a tyre, remove only the centre lug nut, then remove the wheel. If

any further disassembly is required, deflate the tyre completely or it may explode.

WARNING! Wheels on your scooter should only be serviced/replaced by an authorised Pride

Dealer or qualified technician.

Figure 29. Solid Tyre Wheel Removal

AXLE

KEY

WASHER

DRIVE WHEEL NUT

WHEEL CAP

AXLE SLOT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Colt Series Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info