Bedienungsanleitung Pride Cyclone (Seite 36 von 42) (Englisch)

721998

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

36 Cyclone

Any electromechanical device requires occasional troubleshooting. However, most problems that arise can be

solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully

charged or because the batteries are worn down and can no longer hold a charge.

DIAGNOSTIC BEEP CODES

Diagnostic beep codes help you to perform basic troubleshooting quickly and easily. A diagnostic beep code will

sound in the event one of the conditions listed below develops. After you perform the solution associated with the

diagnostic beep code, your Cyclone should resume normal operation.

NOTE: Your Sport Scooter will not run unless the beep code condition is resolved and the Sport Scooter

has been turned off and then turned back on.

X. BASIC TROUBLESHOOTING

What if all the systems on my Cyclone seem to be dead?

n Make certain that the key is in the on position.

n Check that the batteries are fully charged. See V. Batteries and Charging.

n Push in the main circuit breakers reset button. See IV. Your Cyclone.

n Make certain that both battery harnesses are firmly connected to the electronics module and to the battery

terminals. See VIII. Disassembly and Assembly.

n Make sure that the front-to-rear harness is firmly connected to the electronics module. See VIII. Disassembly

and Assembly.

n Be sure the auto shutoff feature hasnt been activated. See V. Batteries and Charging.

n Check the fuses. See XI. Care and Maintenance for fuse replacement.

What if the motor runs but my Cyclone does not move?

n Your Cyclone was probably left in manual freewheel mode.

n When the manual freewheel lever is pulled up, the brakes are disengaged and all power to the transaxle is cut.

n Turn the Sport Scooter key to the off position.

n Push the manual freewheel lever down.

n Turn the Sport Scooter key to the on position to restore normal operation.

BEEP CODE CONDITION SOLUTION

1 beep every 5 seconds Batteries are getting low. Charge batteries as soon as possible.

2 beeps every 5 seconds Batteries are too low to operate the

Cyclone or the charger is operating.

Charge batteries or unplug the charger power

lead from the electrical outlet.

3 beeps every 5 seconds Controller is hot; the Sport Scooter

seems to be losing power.

Shut down your Cyclone for a minimum of

several minutes to allow the controller to

cool.

4 beeps every 5 seconds Wigwag fault; your throttle control

levers are not responding.

Call your authorised Pride provider for

assistance.

6 beeps every 5 seconds The manual freewheel lever is in the

freewheel (up) position.

Turn the Cyclone key to the “off” position,

push the manual freewheel lever to the drive

(down) position, restart your Cyclone.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Cyclone Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info