Bedienungsanleitung Pride Jazzy Air (Seite 27 von 32) (Englisch)

793187

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Jazzy Air www.pridemobility.com 27

VII. CARE AND MAINTENANCE

WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning

agent before applying it to your product. Failure to comply may result in skin irritation or

premature deterioration of upholstery and/or power chair nishes.

WARNING! Never hose off your power chair or place it in direct contact with water. Your power chair

has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth.

WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become

slippery or dry out and crack. Use soapy water and dry the seat thoroughly.

Wheel Replacement

If you have pneumatic tires and you have a at tire, replace the tube. If your chair is equipped with a solid tire

insert, then you must replace the whole wheel assembly. Replacement tires, tubes, and wheel assemblies are

readily available through your authorized Pride Provider.

WARNING! The wheels on your

power chair should only be serviced

or replaced by an authorized Pride

Provider or a qualied technician.

WARNING! Be sure that the power to

the controller is turned off and the

power chair is not in freewheel mode

before performing this procedure.

WARNING! When changing a tire,

remove only the center lug nut and

washer, then remove the wheel. If

any further disassembly is required,

deate the tire completely or it may

explode.

Follow these easy steps for a quick and safe repair

for both pneumatic and solid tires:

1. Turn off the power to the controller.

2. Make sure that the power chair is in drive mode. Seegure4.

3. Raise and support the power base so that the wheel is at least 1 in. (2.5 cm) off of the ground.

4. If you are changing a pneumatic tire, completely deate it before removing the wheel.

5. Remove the hub cap, if equipped. Seegure16.

6. Remove the drive wheel nut and washer from the axle. Seegure16.

7. Remove the drive wheel from the axle. Make sure that you keep the key.

8. Remove the acorn nuts that fasten the two rim halves together.

9. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if

it is a solid tire.

10. Reassemble the two rim halves.

11. Slide the wheel back onto the axle. Make sure that the key is in the axle slot.

WARNING! Ensure that the axle key is properly installed into the axle slot when mounting the

wheel. If not installed securely, the braking system is disengaged which may cause personal

injury and/or product damage may result.

12. Reinstall the drive wheel nut and washer onto the axle and tighten. Seegure16.

WARNING! Make sure both the nut and washer are reinstalled and tightened properly.

13. Reinstall the hub cap, if equipped.

14. Inate the pneumatic tire to the psi/bar/kPa air pressure rating indicated on each tire.

15. Remove the power chair from the base support.

Figure 16. Drive Wheel Removal

MOTOR KEY

AXLE

DRIVE WHEEL WASHER

DRIVE

WHEEL NUT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Jazzy Air Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pride Jazzy Air

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info