Bedienungsanleitung Pride Legend (Seite 29 von 34) (Englisch)

721981

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

29Legend

IX. TROUBLESHOOTING

Any electromechanical device requires occasional troubleshooting. However, most problems that arise can usually

be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not

fully charged or because the batteries are worn down and can no longer hold a charge.

DIAGNOSTIC FLASH CODES

Diagnostic flash codes help you perform basic troubleshooting quickly and easily. A diagnostic flash code will flash

from the status LED in the event one of the conditions listed below develops.

NOTE: Your Scooter will not run unless the flash code condition is resolved and the Scooter has been

powered down then powered back up.

What if all the systems on my Legend seem to be dead?

nMake certain that the key is in the on position.

nCheck that the batteries are fully charged. See V. Batteries and Charging.

nPush in the the main circuit breaker reset button. See IV. Description.

nMake certain that both battery harnesses are firmly connected to the rear electronics module and to the

battery terminals. See VIII. Disassembly and Assembly.

nMake sure that the silver front-to-rear harness is firmly connected to the rear electronics module. See VIII.

Disassembly and Assembly.

nBe sure the auto shutoff feature hasnt been activated. See V. Batteries and Charging.

nCheck the fuses. See X. Care and Maintenance for fuse replacement.

What if the motor runs but my Legend does not move?

nWith the key turned to the on position, check the status LED. If the LED flashes three times, a short pause,

then two times, this is the manual freewheel lever code and means your Legend is in manual freewheel mode.

nWhen the manual freewheel lever is pulled up, the brakes are disengaged and all power to the transaxle is

cut.

nPush down the manual freewheel lever to restore normal operation to your Legend. See IV. Description.

FLASH CODE CONDITION SOLUTION

n n n n n

Batteries are too low to o

erate the

Scooter or the charger is operating. Charge batteries or unplug the charger power

cord from the electrical outlet.

n n

Controller is hot; the Scooter seems to

be losing power.

Shut down your Scooter for a minimum of

several minutes to allow the controller to

cool.

n n n n

fault;

our throttle control

levers are not responding. Call

our authorized Pride

rovider for

assistance.

n n n n n

The manual freewheel lever is in the

(up) freewheel position.

Turn the Scooter key to the off position, then

ush the freewheel lever to the (down) drive

position, restart your Scooter.

n n n n n n

Scooter is operating with the charger

attached. Unplug the charger cord from the charger

power cord receptacle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Legend Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pride Legend

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info