Bedienungsanleitung Pride QUANTUM 610 (Seite 14 von 32) (Englisch)

668245

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

14 www.pridemobility.com Quantum 610 Series

V. COMFORT ADJUSTMENTS

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may ﬁ nd the need to make some adjustments to

increase your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller

position. If your power chair is equipped with power positioning options, refer to the information supplied in

supplemental manuals or contact your Quantum Rehab Provider.

WARNING! The center of gravity of your power chair was factory set to a position that meets

the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated

your power chair and made any necessary adjustments to suit your speciﬁ c requirements. Do

not change your seating conﬁ guration without ﬁ rst contacting your Quantum Rehab Provider.

WARNING! Some power chair components are heavy. You may need assistance to lift or carry

them. Please refer to speciﬁ cations table for speciﬁ c component weights before you disassemble

the power chair.

WARNING! Remove the occupant from the power chair before making any adjustments.

You may need the following to make comfort adjustments:

 metric/standard socket set and ratchet

 adjustable wrench

 thread lock

Seat Height and Seat Angle Adjustment

You can change the seat height to one of four positions in

1-in. (2.54-cm) increments by raising the front and rear

trapeze bars. If you raise or lower only one trapeze bar (front

or rear), you can also change the seat base angle (dump).

To change the seat height:

1. Turn off the power to the controller.

2. Loosen the rear shroud fasteners and remove the rear

shroud. See ﬁ gure 2.

3. Disconnect the controller connector(s) from the power

base. See ﬁ gure 3.

4. Flip up the seat latch safety. See ﬁ gure 11.

5. Squeeze the seat latch and release the seat from the front

trapeze bar. See ﬁ gure 11.

6. Slide the seat forward and remove it from the power

base.

7. Loosen the screws that attach the trapeze bars to the seat

posts. See ﬁ gure 12.

8. Remove the retaining clips that secure the seat posts to

the power base. See ﬁ gure 12.

9. Move the trapeze bars up or down to the desired height.

10. Reinstall the retaining clips from step 8.

11. Remove each screw from the trapeze bars and apply

thread lock.

12. Reinstall each screw into the trapeze bars and tighten.

13. Reinstall the seat and ﬂ ip down the seat latch safety.

14. Reconnect the controller connector(s) to the power base.

15. Reinstall the rear shroud and tighten the fasteners.

Figure 11. Seat Height Adjustment - Seat Latch

Safety

Figure 12. Seat Height Adjustment - Trapeze Bars

SCREWS

(2 OF 4)

TRAPEZE BARS

SEAT POSTS

(2 OF 4)

RETAINING

CLIPS

(2 OF 4)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride QUANTUM 610 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info