Bedienungsanleitung Pride Ranger - MV600 (Seite 13 von 108) (Englisch, Französisch, Spanisch)

721832

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

MV600 13

Manual Freewheel Lever

Whenever you need or want to push your vehicle for short

distances, you can put it in freewheel mode.

1. Remove the key from the key switch.

2. Push forward on the manual freewheel lever to

disable the drive system and the brake system. This

will enable you to push the vehicle.

NOTE: If your vehicle is equipped with a 2-position

manual freewheel lever, you must pull up on the lever

and then push forward on the manual freewheel lever to

disable the drive system and the brake system. This will

enable you to push the vehicle.

3. Pull back on the manual freewheel lever to reengage

the drive and the brake systems and take your vehicle

out of freewheel mode.

IDENTIFICATION KEY

1. MANUAL FREEWHEEL LEVER

2. MOTOR/TRANSAXLE ASSEMBLY

Figure 7. Rear Components

II. YOUR VEHICLE

WARNING! When your vehicle is in freewheel mode, the braking system is disengaged.

 Disengage the drive motors only on a level surface.

 Ensure the key is removed from the key switch.

 Stand to the side of the vehicle to engage or disengage freewheel mode. Never sit on a

vehicle to do this.

 After you have ﬁ nished pushing your vehicle, always return it to the drive mode to lock the

brakes.

NOTE: If the vehicle is placed in freewheel mode (manual freewheel lever forward) while the key is in the “on”

position, the vehicle will not run until the manual freewheel lever is pushed rearward and the key is turned to

the “off” position, then back to the “on” position.

Motor/Transaxle Assembly

The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your vehicle’s

batteries into the controlled mechanical energy that drives the vehicle’s wheels.

Batteries

The batteries store electrical energy that powers your vehicle. See III. “Batteries and Charging ” for information

on how to charge your vehicle batteries.

Back-Up Sensor

Your vehicle is equipped with an automatic backup sensor and reverse light to alert you of objects that may be

behind you. When the vehicle is driven in the reverse direction and a solid obstacle such as a wall is detected, an

audible tone is emitted alerting you to the presence of a detected object. This feature can be turned off using the

switch located on the backup sensor module on the rear of your vehicle.

WARNING! The back up sensor should not take the place of looking behind you prior to and while

driving in a reverse direction. The sensors may not detect objects that are moving, or ones with

poor reﬂ ective properties such as persons, pets or shrubbery.

 To ensure reliable operation, keep the sensor free of dirt, mud, and water.

 If exposed to water, allow sensor to dry before using.

 If sensor screens become covered with dust, debris, or water, wipe with a dry cloth prior to use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Ranger - MV600 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pride Ranger - MV600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info