Bedienungsanleitung Princess 213100 Lets Blender Compact 0.8L - Mill (Seite 11 von 65) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

491650

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

COMPACT BLENDER & MILL (LET’S BLENDER) ART 213100

Grinding

See figure 4.

1 Place the housing on a stable surface.

2 Fit the mill to the housing. The three catches on the housing

must fit precisely into the slots in the base of the mill.

3 Rotate the top plate of the mill clockwise to open the mill-

jug.

4 Fill the mill jug with the product that you wish to grind.

5 Rotate the top plate of the mill anti-clockwise to close the

mill-jug.

6 If the rotary button is in 0-position and pushed in, the button

is locked. Push the rotary button to unlock it (see figure 2).

7 Switch the mill a few seconds to setting 1 or 2 or the pulse

setting (P).

This mill works very fast. In seconds the product will be

ground. The longer the mill is turned on, the finer the

products will be ground.

Note: Do not operate the mill more than 50 seconds

with max. 150 g ingredients. Let the mill cool down for

around 7 minutes before starting again.

8 Switch off the mill (position 0) once the required quantity

has been ground.

9 Push the rotary button to lock it (see figure 2).

10 Remove the plug from the plug socket.

11 Wait until the blades stand still and remove the ground

product.

Cleaning and maintenance

• Make sure the plug has been removed from the plug

socket before cleaning the appliance.

• Make sure no moisture gets into the interior of the

housing.

• Do not immerse the appliance in water or in other liquids.

If this does happen, do not use the appliance again. For

safety reasons, dispose of the appliance.

• Only the separate components may be cleaned in a

dishwasher.

• Never use corrosive or scouring cleaning products.

• This blender uses sharp knives, which are located in the

bottom of the container. Therefore, be very careful when

emptying and cleaning the blender. Avoid cutting

yourself on the knives.

1 Clean the exterior of the housing with a soft, damp cloth.

2 Clean the jugs and the components with warm soapy water.

3 Thoroughly clean the rotating knives at the bottom of the

jug, in particular, and make sure you remove all the food

from them (see ‘Removing and fixing the base with the

rotating knives’).

4 Remove the base from the mill (see removing mill base from

mill).

5 Clean the mill-jug and the components of the mill with warm

soapy water.

6 Thoroughly clean the rotating blades at the bottom of the

jug, in particular, and make sure you remove all the food

from them.

7 Dry the components thoroughly after they have been

cleaned.

Removing and fixing the base with the rotating

knives

See figure 3.

1 Fit the jug to the housing.

2 Hold the housing.

3 Rotate the jug anti-clockwise.

4 Remove the jug from the base with the rotating knives.

5 Remove the base with the rotating knives from the housing.

6 Reassemble the base with the rotating knives and the jug in

the opposite order.

Removing the mill base from mill

See figure 5.

1 Hold the mil and rotate the mill base anti clockwise.

2 Remove the base from the mill-jug.

3 Reassemble the mill in the opposite order.

JdB_ Blenders_213100.book Page 6 Friday, May 16, 2008 4:43 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Princess 213100 Lets Blender Compact 0.8L - Mill Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info