Bedienungsanleitung Princess 2522 (Seite 6 von 24) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

8047

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Adjustable screw for setting tilt angle (16)

This allows the direction that the fan blows to be set at the desired angle. Loosen the screw a couple of

turns by hand and tilt the fan up or down as desired. Then retighten the screw firmly by hand.

Height adjustment (4)

The height can be adjusted by loosening the nut on the stand. Once the correct height has been set

tighten up the nut again.

PARTS

1. base

2. base screw

3. outer tube

4. height adjustment nut

5. inner tube

6. speed control

7. motor shaft

8. rear guard

9. screw

10. fan blade

11. fan blade screw

12. front guard

13. screw and nut

14. oscillation knob

15. tilt control screw

16. knob

ASSEMBLING THE FAN

1. Position the rear guard over the motor shaft, ensuring that the notches are

correctly aligned and then secure with four screws.

2. Align the fan blade with the flat part on the motor shaft, locate fully

and secure by tightening the fan blade screw fully. The screw should

be positioned between the motor housing and the blade.

3. With the help of another person, position the front guard against the

rear guard and press the clips so that it holds both grills together and

the screw is at the bottom. Secure by tightening screw and nut.

ASSEMBLING THE STAND

1. Slide the cover plate up the shaft and attach the flange of the outer tube to the base using the nuts and

bolts provided. Check nuts are fully tightened before replacing the cover plate.

2. Unscrew the height adjustment knob, and pull up the inner tube to adjust the height, ensuring that the

knob is fully tightened before proceeding.

3. Position the fan head motor either side as shown on the left figure and insert the tilt control bolt so that

it passes through the square hole of the coupling and the lower hole of inner tube. Fully tighten the

small screw that is already located in the coupling and then fit the knob onto the tilt control bolt and

lightly tighten.

4. Insert the locking screw through the top hole of the coupling, adjust the fan head to the desired position

and firmly tighten screw and the tilt control.

CLEANING

FIRST UNPLUG THE CORD FROM THE SOCKET

The fan can be wiped with a damp cloth now and then. Never use abrasive or aggressive

detergents, thus no scouring powder and no scouring sponges either.

NEVER IMMERSE THE FAN IN WATER OR OTHER LIQUID.

PRINCESS TIPS

- This fan is intended for normal household use only.

- Make sure the cord or extension cord is carefully positioned to avoid people tripping

over it.

- If the fan or cord is damaged, we advise you not to use the appliance and to take it to

the shop for repair. Damaged cords may only be replaced by the service department.

- Not to be used outdoors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Princess 2522 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Princess 2522

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info