Bedienungsanleitung Privileg RBO3C34X (Seite 8 von 8) (Englisch)

712434

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Your dishwasher may not work properly.

Before contacting the Service Centre check if the problem can be solved by going through the following list.

PROBLEMS POSSIBLE CAUSES SOLUTIONS

The dishwasher

won’t start

or does not

respond to

commands.

The appliance has not been plugged

in properly.

Insert the plug into the socket.

Power outage. The dishwasher starts automatically when the power returns.

The dishwasher door is not closed. Vigorously push the door until you hear the “click”.

It does not respond to commands.

Switch o the appliance by pressing the ON/OFF button, switch it back

on after approximately one minute and reset the program.

The dishwasher

won’t drain.

The wash cycle has not nished yet. Wait until the wash cycle nishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The lter is clogged up with food

residues.

Clean the lter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes

excessive

noise.

The dishes are rattling against each Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has

been produced.

The detergent has not been measured out correctly or it is not suita-

ble for use in dishwashers (see FILLING THE DETERGENT DISPENSER).

Reset dishwasher by pressing the DRAIN button (see OPTIONS AND

FUNCTIONS) and run new program without detergent.

The dishes are

not clean.

The crockery has not been arranged

properly.

Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely,

being hindered by the dishes.

Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has

been produced.

The detergent has not been measured out correctly or it is not suitable

for use in dishwashers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment

has not been shut correctly.

Make sure the cap of the rinse aid dispenser is closed.

The lter is soiled or clogged. Clean the lter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

TROUBLESHOOTING

400011266605B

08/2019 jk - Xerox Fabriano

MAINTENANCE AND TROUBLESHOOTING GUIDE

For more information, maintenance procedures and tro-

ubleshooting, see the Use and Care Guide

The Use and Care Guide can be obtained by:

• After-Sales Service; phone number see in warranty

booklet.

• download from website: docs.whirlpool.eu

• use QR code

CONTACTING AFTER-SALES SERVICE

When you contact the After-Sales Service, you must pro-

vide the codes shown on the rating plate attached to the

left or right side inside the door of the dishwasher.

The phone number is listed

in the warranty booklet or on the

website:

www.privileg.de

TECHNICAL DATASHEET

The technical data containing the energy consumption

data can be downloaded from the website:

docs.whirlpool.eu

IEC 436

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Privileg RBO3C34X Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Privileg RBO3C34X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info