Bedienungsanleitung Pro-form 585 CSE - PFEL95918 (Seite 22 von 28) (Englisch)

553935

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Inspect and tighten all parts of the elliptical exerciser

egularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and

a small amount of mild soap. IMPORTANT: To avoid

amage to the console, keep liquids away from

the console and keep the console out of direct

sunlight.

HOW TO ADJUST THE DRIVE BELT

If the pedals slip while you are pedaling, even while

the resistance is adjusted to the highest setting, the

drive belt may need to be adjusted. To adjust the drive

belt, see assembly step 11 on page 11 and remove

the Left Pedal Leg (24) and the Left Link Arm (25).

Then, see EXPLODED DRAWINGAnear the end of

this manual and remove the M6 x 25mm Button Screw

(61) from the center of the left Crank Arm Cover (32),

and then carefully remove the left Crank Arm Cover.

Next, remove all the screws from the left shield, and

then carefully remove the left shield.

Loosen, but do not

remove, the three

screws (A). Insert

the shaft of a

screwdriver down-

ward between the

Idler (12) and the

pulley located on

the Eddy

Mechanism (10).

Pull the top of the

screwdriver toward

the rear of the

elliptical exerciser until the Belt (84) is tight, and then

tighten the three screws.

Reattach the left shield and the left crank arm cover.

Then, see step 11 on page 11 and reattach the left

pedal leg and the left link arm.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the

reed switch should be adjusted. To adjust the reed

switch, first see EXPLODED DRAWINGAnear the

end of this manual and remove the M6 x 25mm Button

Screw (61) from the center of the right Crank Arm

Cover (32), and then carefully remove the right Crank

Arm Cover.

Next, remove all the screws from the left shield, and

hen carefully remove the left shield.

See the drawing below and locate the Reed Switch

(21). Loosen, but do not remove, the indicated M4 x

6mm Screw (72). Slide the Reed Switch slightly closer

to or away from the Magnet (18) on the Pulley (13).

Then, retighten the M4 x 16mm Screw (72). Turn one

of the CrankArms (31) for a moment. Repeat until the

console displays correct feedback. When the Reed

Switch is correctly adjusted, replace the crank arm

cover.

CONSOLE TROUBLESHOOTING

If the console display becomes dim, the batteries

should be replaced; most console problems are the

result of low batteries. See assembly step 6 on page 8

for replacement instructions. If the console does not

display your heart rate when you hold the handgrip

pulse sensor, or if the displayed heart rate appears to

be too high or too low, see step 5 on page 15.

HOW TO LEVEL THE ELLIPTICAL EXERCISER

If the elliptical exerciser rocks slightly on your floor

during use, see HOW TO LEVEL THE ELLIPTICAL

EXERCISER on page 12.

HOW TO GREASE THE ROLLERS

See the EXPLODED DRAWING near the end of this

manual. If the Rollers (27) squeak when moving on

the Track (2), apply the contents of the included pack-

et of white marine grease equally to each Roller.

Spread the grease evenly around the Rollers. Pedal

the elliptical exerciser until a thin film of grease is dis-

tributed along the Track; wipe off any excess grease.

MAINTENANCE AND TROUBLESHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form 585 CSE - PFEL95918 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info