Bedienungsanleitung Pro-form 905 ZLT - PETL11810 (Seite 18 von 36) (Englisch)

553938

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

old temperatures, allow it to warm to room tem-

perature before turning on the power. If you do not

o this, you may damage the console displays or

other electrical components.

Plug in the power cord (see

page 16). Next, locate the

power switch on the tread-

mill frame near the power

cord. Make sure that the

switch is in the reset

position.

IMPORTANT: The console features a display demo

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as

you plug in the power cord and press the power

switch into the reset position, the demo mode is

turned on. To turn off the demo mode, hold down

the Stop button for a few seconds. If the displays

remain lit, see THE INFORMATION MODE on page

22 to turn off the demo mode.

Next, stand on the foot rails

of the treadmill. Locate the

clip attached to the key

(see the drawing at the

right), and slide the clip se-

curely onto the waistband

of your clothes. Then, insert

the key into the console.

After a moment, the displays will light. IMPORTANT:

In an emergency situation, the key can be pulled

from the console, causing the walking belt to slow

to a stop. Test the clip by carefully taking a few

steps backward; if the key is not pulled from the

console, adjust the position of the clip.

Note: The console can display speed and distance in

either kilometers or miles. To find which unit of mea-

surement is selected, see THE INFORMATION MODE

on page 22. For simplicity, all instructions in this

manual refer to kilometers.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER at the left.

2. Select the manual mode.

Each time the key is in-

serted, the main menu

will appear. To select

the manual mode, use

the increase and de-

crease buttons next to

the Enter button and

highlight START. Press the Enter button. Note: If

you have selected a workout or the iFit training

mode, press the Menu button to return to the main

menu.

3. Start the walking belt and adjust the speed.

To start the walking belt, press the Start button, the

Speed increase button, or one of the speed but-

tons numbered 2 to 20.

If you press the Start button or the Speed increase

button, the walking belt will begin to move at 2

Km/H. As you exercise, change the speed of the

walking belt as desired by pressing the Speed in-

crease and decrease buttons. Each time you press

one of the buttons, the speed setting will change

by 0.1 Km/H; if you hold down the button, the

speed setting will change in increments of 0.5

Km/H.

If you press one of the numbered speed buttons,

the walking belt will gradually change speed until it

reaches the selected speed setting.

To stop the walking belt, press the Stop button. To

restart the walking belt, press the Start button, the

Speed increase button, or one of the numbered

speed buttons.

Key

Reset

Clip

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form 905 ZLT - PETL11810 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pro-form 905 ZLT - PETL11810

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info