Bedienungsanleitung Pro-form 910 ZLT - PETL10812 (Seite 14 von 36) (Englisch)

553929

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

HOW TO PUT ON THE HEART RATE MONITOR

The heart rate

monitor consists of

a chest strap and a

sensor. Insert the

tab on one end of

the chest strap into

the hole in one end

of the sensor as

shown. Then, press

the end of the sen-

sor under the buckle

on the chest strap.

The tab should be

flush with the front of

the sensor.

The heart rate moni-

tor must be worn

under your clothes,

tight against your

skin. Wrap the heart

rate monitor around

your chest in the

location shown.

Make sure that

the logo is right-

side-up. Then, attach the other end of the chest strap

to the sensor. Adjust the length of the chest strap, if

necessary.

Pull the sensor away from your body a few inches and

locate the two electrode areas, which are covered by

shallow ridges. Using saline solution such as saliva or

contact lens solution, wet the electrode areas. Then,

return the sensor to a position against your chest.

CARE AND MAINTENANCE

• Thoroughly dry the sensor with a soft towel after

each use. Moisture may keep the sensor activated,

shortening the life of the battery.

• Store the heart rate monitor in a warm, dry place.

Do not store the heart rate monitor in a plastic bag

or other container that may trap moisture.

• Do not expose the heart rate monitor to direct sun-

light for extended periods of time; do not expose it

to temperatures above 122° F (50° C) or below 14°

F (-10° C).

• Do not excessively bend or stretch the sensor when

using or storing the heart rate monitor.

• To clean the sensor, use a damp cloth and a small

amount of mild soap. Then, wipe the sensor with a

damp cloth and thoroughly dry it with a soft towel.

Never use alcohol, abrasives, or chemicals to clean

the sensor. Hand wash and air dry the chest strap.

TROUBLESHOOTING

If the heart rate monitor does not function properly, try

the steps below.

• Make sure that you are wearing the heart rate mon-

itor as described at the left. If the heart rate monitor

does not function when positioned as described,

move it slightly lower or higher on your chest.

• If heart rate readings are not displayed until you

begin perspiring, rewet the electrode areas.

• For the console to display heart rate readings, you

must be within arm’s length of the console.

• If there is a battery cover on the back of the sensor,

replace the battery with a new battery of the same

type.

• The heart rate monitor is designed to work with

people who have normal heart rhythms. Heart rate

reading problems may be caused by medical condi-

tions such as premature ventricular contractions

(pvcs), tachycardia bursts, and arrhythmia.

• The operation of the heart rate monitor can be

affected by magnetic interference from high power

lines or other sources. If you suspect that magnetic

interference is causing a problem, try relocating the

fitness equipment.

THE CHEST HEART RATE MONITOR

Sensor

Buckle

Tab

Chest

Strap

Tabs

Sensor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form 910 ZLT - PETL10812 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pro-form 910 ZLT - PETL10812

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info