Bedienungsanleitung Pro-form G880 (Seite 14 von 18) (Englisch)

708084

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

32. Wrap the Butterfly Cable (83) under a 90mm

Pulley (90). Attach the Pulley and two Half Finger

Guards (133) to the Double “U”-bracket (73) with

an M10 x 47mm Bolt (136) and an M10 Nylon

Locknut (97).

33. Wrap the Butterfly Cable (83) over a “V”-pulley

(89). Attach the “V”-pulley, a Large Cable Trap

(88), and two Finger Guards (134) to the Center

Upright (37) with an M10 x 62mm Bolt (128) and

an M10 Nylon Locknut (97). Make sure the

Cable Trap is oriented to hold the Cable in the

groove of the “V”-pulley.

34.

Attach the Butterfly Cable (83) to the Right Fly

Arm (43) with an M8 x 16mm Shoulder Bolt (129)

and an M8 Nylon Locknut (96). Make sure that

the Cable can pivot freely around the Bolt.

134

128

134

129

31. Wrap the Butterfly Cable (83) over a “V”-pulley

(89). Attach the “V”-pulley, a Large Cable Trap (88),

nd two Finger Guards (134) to the Center Upright

(37) with an M10 x 62mm Bolt (128) and an M10

ylon Locknut (97). M

ake sure the Cable Trap is

oriented to hold the Cable in the groove of the

“V”-pulley.

136

133

28. Attach the Butterfly Frame (42) to the Rear Top

Frame (39) with two M10 x 78mm Bolts (110), two

10 Washers (99), and two M10 Nylon Locknuts

(97).

Do not tighten the Locknuts yet.

Attach the Butterfly Frame (42) to the Center

Upright (37) with two M10 x 68mm Bolts (113),

two M10 Washers (99), and two M10 Nylon

Locknuts (97). Do not tighten the Locknuts yet.

Tighten all of the M10 Nylon Locknuts (97)

used in steps 11–28. Tighten the 1/4” x 14mm

Screws (119) used in step 22 and the 1/4” x

9.5mm Allen Head Set Screws (120) used in

step 23.

30. During cable assembly

, see the CABLE DIA-

GRAMS on page 22 for cable identification

and to verify cable routing.

Locate the Butterfly Cable (83).

Attach the

Cable to the Left Fly Arm (44) with an M8 x

16mm Shoulder Bolt (129) and an M8 Nylon

Locknut (96).

Make sure that the Cable can

pivot freely around the Bolt.

29. Apply grease to both axles on the Butterfly Frame

(42).

Insert a Fly Arm Bushing (92) into the Right Fly

Arm (43). Wet the end of the Arm with soapy

water and slide a Fly Foam Pad (95) onto it.

Have another person slide the Right Fly Arm (43)

onto the right axle on the Butterfly Frame (42).

Note: Be careful not to confuse the Left Fly

Arm (44) with the Right Fly Arm. Make sure

that the upper end of the Arm is behind the

indicated bracket on the Butterfly Frame.

Tap two 25mm Retainer Rings (93) onto the axle of

the Butterfly Frame (42) with the included retainer

tool. Make sure that the teeth on the Retainer

Rings bend toward the tool, as shown in the

inset drawing. Tap the 25mm Round Outer Cap

(94) onto the right axle on the Butterfly Frame.

Attach the Left Fly Arm (44) in the same

manner.

113

Grease Axle

Axle

Bracket

129

Retainer

Tool

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form G880 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pro-form G880

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info