Bedienungsanleitung Pro-form Power 995i - PFTL99715 (Seite 21 von 40) (Englisch)

647860

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do

not do this, you may damage the console displays

or other electrical components.

Plug in the power cord (see

page 19). Next, locate the

power switch on the tread-

mill frame near the power

cord. Press the power

switch into the reset

position.

Next, stand on the foot rails of the treadmill. Find the

clip attached to the key and slide the clip onto the

waistband of your clothes. Then, insert the key into the

console. After a moment, the displays will light.

IMPORTANT: In an

emergency, the key

can be pulled from

the console, caus-

ing the walking

belt to slow to a

stop. Test the clip

by carefully taking

a few steps back-

ward; if the key is

not pulled from the

console, adjust the position of the clip.

IMPORTANT: Before you use the treadmill, take

the following steps to ensure that the console

shows the correct incline level of the treadmill:

First, press the Incline increase button once. Next,

press either the Incline decrease button or the low-

est Quick incline button to set the treadmill to its

lowest setting. When the frame stops moving, the

treadmill is ready for use.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER at the left.

2. Select the manual mode.

Press the Manual Control button to select the

manual mode.

3. Enter your weight.

Press the Wt increase or decrease button to enter

your weight. This information will improve the accu-

racy of the power ring. Note: Press and hold the Wt

increase or decrease button to enter your weight

more quickly.

4. Start the walking belt.

To start the walking belt, press the Run button or

one of the Quick speed buttons.

If you press the Run button, the walking belt will

begin to move at 1 mph. As you exercise, change

the speed of the walking belt as desired by press-

ing the Speed increase and decrease buttons.

Each time you press one of the buttons, the speed

setting will change by 0.1 mph; if you hold down

the button, the speed setting will change in incre-

ments of 0.5 mph. Note: After you press the button,

it may take a moment for the walking belt to reach

the selected speed setting.

If you press one of the Quick speed buttons, the

walking belt will gradually change speed until it

reaches the selected speed setting. To select a

speed setting that includes a decimal—such as 3.5

mph—press two numbered buttons in succession.

For example, to select a speed setting of 3.5 mph,

press the 3 button and then immediately press the

5 button. Note: This option will not function if the

console is set to metric units.

To stop the walking belt, press the Stop button.

The time will begin to ﬂ ash in the display. To restart

the walking belt, press the Run button or the Quick

speed buttons.

Reset

Clip

Key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form Power 995i - PFTL99715 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info