Bedienungsanleitung Probuilder 43637 (Seite 26 von 32) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

789272

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Angling the handle

Hold the release button (5) down and turn

the handle to the required angle from 0 to 90

degrees.

Let go of the release button and turn the

handle slightly until it clicks into the selected

position.

Use

Insert the required bit directly into the

screwdriver’s bit holder (1) or use the

magnetic holder as an extender between the

bit holder and bit.

Turn the torque selector to the required

setting. The higher the setting, the more

power used to screw the screw in.

Change the direction by pushing the switch

(8) to the right or left. If the switch is in the

middle position, the spindle is locked and

you can tighten or loosen screws by turning

the tool itself without it running.

Switch the screwdriver on and oﬀ using the

on/oﬀ button (5).

When the screwdriver is running, the work

light (10) automatically comes on.

Cleaning and maintenance

Wipe down using a well-wrung cloth after

use, and always keep the surface and

ventilation holes free of dirt.

Never use corrosive or abrasive detergents,

as these may aﬀ ect the plastic parts of the

screwdriver.

If the screwdriver will not be used for a

prolonged period, fully charge it before

putting it away. Charge it at least once every

3 months to maintain the battery capacity.

Red and yellow light up:

The battery is partially charged.

Red only:

The battery must be charged before you can

continue using the screwdriver.

Do not use damaged or worn screw bits and

always select the correct type of bit for the

job.

Secure small items in a vice or similar. Never

hold the item in your hand!

Check for concealed power cables, pipes, etc.

in the items you are going to screw into. Do

not touch the plastic parts of the screwdriver

during use on masonry.

Make sure that the screw does not damage

any objects under or behind the item, e.g.

when screwing into walls.

Make sure the screwdriver has stopped

completely before changing direction.

Charging the battery

Charge the battery fully before using the

screwdriver for the � rst time.

Plug the adapter provided into the mains

socket and insert the charging connector

into the charging socket (6) on the

screwdriver.

A full charge takes 3-5 hours.

Never charge for more than 5 hours at a

time.

Unplug the adapter from the mains socket

after charging.

Checking the battery charging

status

Press the button (4) down and read oﬀ the

battery charging status on the LED battery

indicator.

Red, yellow and green light up:

Battery is fully charged.

Special safety requirements

Only charge the battery at room temperature

(max. 40° C).

Never charge the battery if the screwdriver,

adapter or cord is damaged.

Check that the ventilation slots on the

screwdriver are not blocked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Probuilder 43637 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info