Bedienungsanleitung Profile PAC-300 Pavane (Seite 1 von 2) (Englisch)

566709

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

PAVANE – Cordless doorbel set UK - 1

PAC-300

Thank you for purchasing this Profile product.

Please note: It is important that you read this

manual before using the product. And be sure

to save this manual for possible use later.

The cordless doorbell consists of 2 separate

components:

1. Push-button unit (transmitter)

2. Bell unit (receiver)

These items are completely independent of

each other and require no wiring.

When the push-button is pressed in, a signal is

sent to the bell, whereupon the bell is

activated.

Battery installation

Push-button unit

1. The push-button unit works using 1 x 3v

(CR2032) lithium battery (included).

2. The lithium battery is already installed.

Open the push-button and remove the

insulator strip.

3. Snap the rear side back into position, and

the push-button is ready for use.

To replace the battery:

1. Open up the push-button unit.

2. Remove the metal plate using a

screwdriver.

3. Place a 3v battery (CR2032) in the battery

compartment, making sure the positive

terminal (+) is uppermost.

Installation

Push-button unit

Use the two small holes on the rear of the

push-button to mark the position for securing in

place. Drill small holes and mount the push-

button in position with screws (self-tapping 3 x

16mm, included) or use the double-sided

adhesive tape (included).

Important: If you secure the push-button onto

a metal upper surface or PVC type of door

(with metal), its maximum range of

transmission will be greatly reduced.

Bell unit

1. A/C 230volt~50Hz

2. Stick the bell unit in a suitable plug, it is

ready for use immediately. (the green LED

light comes on)

3. Test the bell to make sure the gong is

within reach of the push button.

4. The plug can be used up to 230V, with a

maximum of 13A.

5. The bell has an autodidactic code-system.

Once connected, a 2 tone signal means it

is ready to learn a new code.

Choice of bell tone

The bell-tone selector button is inside the

push-button unit, below letter “S”. Press the

button once to hear the bell tone already set.

Press again to hear and select the next tune.

1. Long Westminster chime 2. Ding-Dong

3. Telephone ring 4. Circus

theme

5. Banjo on my knee 6. Twinkle-twinkle

7. It’s a small world 8. Barking dog

Optionally: It is possible to instal an extra

push-button by your back door. By applying the

procedure given above, each push-button can

produce a different tune.

Channel selection

The unit is supplied with a pre-set radio

frequency. If by chance the bell should sound

for no apparent reason, it's possible that

another device nearby is using the same

frequency. To get round this problem, you can

change the frequency of the push-button and

bell.

1. remove the cover behind the push-button.

2. To program or change: remove the

batteries from the bell unit for at least 30

seconds to prime the memory.

3. place the batteries back into position

within. Press the push-button after the two-

tone signal sound (with a second press of

the button if need be) to confirm the new

code. Do this within 1 minute. Don’t use

any other cordless products for the next 5

minutes.

4. Test for correct operation.

Volume selection

There is a volume-selector button inside the

bell unit to set at the desired bell volume.

Trouble-shooting and tips

Problem: Bell rings, but LEDs

fail to light up

Possible cause:- The bell is out-of-range

(max. 80m in open spaces)

Possible solution: - Move the bell within

range

- Reprogram the channel

(see channel selection)

Problem: Bell does not ring, nor do the

LEDs light up

Possible cause:- Push-button battery is flat

- Batteries are not correctly

installed in the push-button

Possible solution: - Replace battery

- Reinstall the batteries in their

correct positions (see battery

installation for push-button

unit)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PAC-300 Pavane Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PAC-300 Pavane

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info