Bedienungsanleitung Profile PAC-324 Da Segno (Seite 1 von 2) (Englisch)

566741

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

DA SEGNO SET – Cordless doorbel set UK - 1

PAC-324

The cordless doorbell consists of 2 separate

components:

1. Push-button unit (transmitter)

2. Bell unit (receiver)

These items are completely independent of each

other and require no wiring.

When the push-button is pressed in, a signal is sent

to the bell, whereupon the bell is activated. Since it

has a range of up to 100 metres (in open spaces)

you can use the bell virtually anywhere in the house,

workshop, office, set it up in the garden or just carry

it with you.

Battery installation

Push-button unit

1. The push-button unit works using 1 x 3v

(CR2032) lithium battery (included).

2. The lithium battery is already installed.

Open the push-button and remove the

insulator strip.

3. Snap the rear side back into position, and

the push-button is ready for use.

To replace the battery:

1. Open up the push-button unit.

2. Remove the metal plate using a

screwdriver.

3. Place a 3v battery (CR2032) in the battery

compartment, making sure the positive

terminal (+) is uppermost.

Bell unit

1. Slide the rear cover open.

2. Place 2 C alkaline batteries into the battery

compartment.

3. The bell unit will produce a two-tone signal,

indicating that it is ready to read a digital

code (see channel selection).

4. Slide the cover firmly back into place; the

bell is now ready for use.

Installation

Push-button unit

Use the two small holes on

the rear of the push-button to

mark the position for

securing in place. Drill small

holes and mount the push-

button in position with

screws (self-tapping 3 x

16mm, included) or use the

double-sided adhesive tape

(included).

Important: If you secure the

push-button onto a metal

upper surface or PVC type of door (with metal), its

maximum range of transmission will be greatly

reduced.

Bell unit

This bell can be used as a portable device - or fixed

into position. On the reverse side, there are two

suspension slots, with which the bell can be hung

up using a screw, and can easily be taken down

again.

Choice of bell tone

The bell-tone selector button is inside the push-

button unit, below letter “S”. Press the button once

to hear the bell tone already set. Press again to

hear and select the next tune.

1) Westminster 2) Ding Dong

3) Ding-Dong-Ding 4) Tubular – 1

5) Orchestra 6) Tubular – 2

7) Trumpet 8) Dog Barking

Optionally: It is possible to instal an extra push-

button by your back door. By applying the procedure

given above, each push-button can produce a

different tune.

Channel selection

The unit is supplied with a pre-set radio frequency. If

by chance the bell should sound for no apparent

reason, it's possible that another device nearby is

using the same frequency. To get round this

problem, you can change the frequency of the push-

button and bell.

1. remove the cover behind the push-button.

2. To program or change: remove the

batteries from the bell unit for at least 30

seconds to prime the memory.

3. place the batteries back into position

within. Press the push-button after the two-

tone signal sound (with a second press of

the button if need be) to confirm the new

code. Do this within 1 minute. Don’t use

any other cordless products for the next 5

minutes.

4. Test for correct operation.

LED function

When the push-button is pressed, the gong will

sound. At the same time the blue LEDs will also

light up - ideal for the hard of hearing or when using

in a noisy environment. The light will show for

approx. 10 sec in order to attract the attention. If use

of LEDs is not required, they can be switched off by

means of the on/off button at the battery

compartment.

Mode function

1 x push: light and sound

2 x push: light

3 x push: sound

Volume selection

There is a volume-selector buttonat the pack of the

bell unit.

Trouble-shooting and tips

Problem:

Bell rings, but LEDs fail to light up

Possible cause:

The bell is out-of-range (max. 100m in open

spaces)

Push-button and bell are not set to the same

frequency

Possible solution:

Move the bell within range

Reprogram the channel (see channel selection)

Problem:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PAC-324 Da Segno Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PAC-324 Da Segno

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info