Bedienungsanleitung Profile PAC-354 Andante (Seite 6 von 13) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

566745

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ANDANTE – Cordless doorbel set UK - 1

PAC-354

Thank you for purchasing this Profile product.

Please note: It is important that you read this

manual before using the product. And be sure to

save this manual for possible use later.

The cordless doorbell consists of 2 separate

components:

1. Push-button unit (transmitter)

2. Bell unit (receiver)

These items are completely independent of each

other and require no wiring.

When the push-button is pressed in, a signal is sent

to the bell, whereupon the bell is activated. Since it

has a range of up to 100 meters (in open spaces)

you can use the bell virtually anywhere in the

house, workshop, office, set it up in the garden or

just carry it with you.

Battery installation

Push-button unit

1. The push-button unit works using 1 x 12v

battery (included).

2. The battery is already installed.

3. To replace the battery (fig 1):

1. Open up the push-button unit.

2. Place a 12v battery in the battery

compartment, making sure the

positive terminal (+) is uppermost.

Bell unit

1. Slide the rear cover open.

2. Place 2 AA alkaline batteries into the

battery compartment.

3. Slide the cover firmly back into place; the

bell is now ready for use.

Installation

Push-button unit (fig 2)

Use the two small holes on the rear of the push-

button to mark the position for securing in place.

Drill small holes and mount the push-button in

position with screws (included) or use the double-

sided adhesive tape (included).

Important: If you secure the push-button onto a

metal upper surface or PVC type of door (with

metal), its maximum range of transmission will be

greatly reduced.

Bell unit

This bell can be used as a portable device - or fixed

into position. On the reverse side, there is a

suspension slot, with which the bell can be hung up

using a screw, and can easily be taken down again.

Drill a small hole and fix a rawl plug in place and

add the screw. The bell unit can hung up safely in

this way.

Choice of bell tone

The bell-tone selector button is inside the push-

button unit and bell unit (fig 3 & 4). Press the

button once to hear the bell tone already set. Press

again to hear and select the next tune.

Channel selection

The unit is supplied with a pre-set radio frequency.

Warning

1. Do not fasten the push-button onto a metal

upper surface or PVC type of door. This

restricts their range.

2. Do not expose the bell unit to direct rain,

splashing water or direct sunlight, and do not

immerse the unit in water.

3. Do not drop the bell or push-button, or

subject them to severe insults.

4. Do not expose either unit to high

temperatures, nor place them close to

sources of heat.

5. Never combine different types of batteries,

nor use old and new batteries together.

6. Always use alkaline batteries: they will last

longer and there is less risk of leakage.

7. If the bell will be out of use for a prolonged

period, remove the batteries.

8. The bell unit is suitable for use indoors only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PAC-354 Andante Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info