Bedienungsanleitung Profile PLI-141 (Seite 7 von 18) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

566839

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

LAMP WITH ENERGY-SAVING LIGHT EN - 1

PLI-141

We thank you for the purchase of this Profile product.

Note: It is important that you read this manual carefully

before using the product and be sure to save this

manual for possible use later.

Note

Check if building regulations apply to your area

whereby you must have the lamp installed by an

accredited electrician. An electrician can give you

information about correct wiring. Never install the fitting

outside in rainy weather.

SWITCH OFF THE POWER BEFORE YOU INSTALL

THE LAMP.

Correct installation

 With installation outside preferably choose a place

under a roof.

 Connect the lamp to a circuit with wall switch.

 Unscrew the stainless steel bolts on the side to take

the holder from the fitting.

 Fix the holder to the wall with 2 screws.

 Fix the lamp back on the assembled holder.

 Remove the cover of the cable connection.

 Pull the power supply wires through the opening with

the rubber packing.

 The lamp must be connected to mains voltage of

230V, max. fusing 16A.

 Connect the wires according to figure 1.

 Screw the cable connection cover tight again.

 Always respect the instructions on the identification

label of the connected power cables.

 Other uses than described above can cause damage

to the product and increase the risk of short-circuit,

fire, electric shocks, etc.

Fig.1

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

Safety instructions

 The importer accepts no responsibility for damage

claims with respect to objects or persons that result

from incorrect use or non-compliance with the safety

instructions. Any damage claims in such cases will

be declared null and void.

 When replacing the R7S 32W energy-saving light the

power supply must be switched off. Do not exceed

the maximum wattage of 32W.

 Always replace cracked or broken glass by glass

with the same properties as the original glass.

Technical information

 Working voltage: 230V AC (50/60 Hz)

 Maximum lamp power: 32W

 Maximum current strength: 10/16A

 Dustproof and splashproof: IP44.

 Passive infrared sensor (PIR)

 Sensor angle: 120°

 Sensor range: 10 metres at with 25°C.

 Lighting time: +/- 5 sec. – 8 min.

Setting the functions

1) Setting the light intensity (lux)

With the LUX Switch you adjust the working of the

sensor to match the intensity of the ambient light.

If the arrow is pointing to the sun the sensor responds

in both daylight and at night.

If the arrow is pointing to the moon the sensor will only

respond at night.

In between the sensor responds in half-light.

2) Setting the lighting time (TIME)

With this adjusting knob you can set the period of the

light staying on after switching on. You can set the

time from 5 sec. to 8 min.

Continuous function

With this function you can allow the lamp to stay on

continuously (the sensor then no longer works).

To do this switch the switch the fitting is connected to

on and off for 1 second. The lamp will now stay on

continuously.

To switch off the continuous function switch the switch

the fitting is connected to off for 30 seconds and then

on again.

Maintenance

 Only use a dry, soft cloth for cleaning the lamp.

 Never immerse the lamp in water.

 Maintenance and repairs may only be carried out by

technicians who are familiar with any applicable

regulations.

Guarantee conditions

The guarantee period for PLI-141 amounts to 2 years

and commences on the date of purchase. During the

guarantee period ELTRA nv will repair any defects

attributable to material or production faults. ELTRA NV

may choose to either repair or replace a defective

appliance.

ELTRA NV is not obliged to repair or replace

appliances if they have become defective as a result of

* L = phase

= earthing

* N = neutral wire

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PLI-141 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info