Bedienungsanleitung Profile PLI-176 (Seite 1 von 2) (Englisch)

566869

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

HALOGEN HAND LAMP 300W SKY

EN - 1

PLI-176

We thank you for the purchase of this Profile product.

Note: It is important that you read this manual

carefully before using the product And be sure to save

this manual for possible use later.

Note

Check if building regulations apply to your area

whereby you must have the halogen hand lamp

installed by an accredited electrician. An electrician

can give you information about correct wiring. Never

install the fitting outside in rainy weather.

SWITCH OFF THE POWER BEFORE YOU INSTALL

THE HALOGEN HAND LAMP.

Correct installation

 With installation outside preferably choose a place

under a roof.

 Do not place the sensor head in direct or reflected

sunlight. The halogen hand lamp may then switch

on when not required. The sensor works best with

movement “crosswise” through the sensor's

detection field.

 Connect the halogen hand lamp to a circuit with wall

switch.

 Unscrew the stainless steel bolts on the side to take

the holder from the fitting.

 Fix the holder to the wall with 2 screws. Do not fix

the holder to a highly flammable surface. Leave a

distance of at least 1 m between the halogen hand

lamp and the object to be illuminated. (see fig. 2)

Install the halogen hand lamp at least 2.5 m above

the ground. (see fig.1)

Fig. 1 Fig. 2

 CAUTION: There is an “UP” arrow on the inside of

the holder. The arrow must point upwards when you

mark the position of the holes.

Fig. 3

 Pull the power supply wires through the opening

with the rubber packing.

 Connect the electric wiring according to figures 4

and 5.

 The halogen hand lamp must be connected to

mains voltage of 230V, max. fusing 16A.

Fig. 4

Fig. 5

 Screw the cable connection cover tight again.

 Always respect the instructions on the identification

label of the connected power cables.

 Other uses than described above can cause

damage to the product and increase the risk of

short-circuit, fire, electric shocks, etc.

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

Safety instructions

 The importer accepts no responsibility for damage

claims with respect to objects or persons that result

from incorrect use or non-compliance with the

safety instructions. Any damage claims in such

cases will be declared null and void.

 When replacing the halogen bulb the lamp must

first have cooled before the bulb is replaced. Also

disconnect the power supply. Do not exceed the

maximum wattage of 300W.

 CAUTION: Never touch the bulb with your fingers.

Touching the bulb with your fingers can reduce the

life of the bulb.

 Always replace cracked or broken glass by glass

with the same properties as the original glass.

Technical information

 Working voltage: 230V AC (50/60 Hz)

 Maximum lamp power: 300W.

 Maximum current strength: 10/16A.

 Dustproof and splash proof: IP44.

Maintenance

 Only use a dry, soft cloth for cleaning the halogen

hand lamp. And make sure that the lamp has first

cooled.

 Never immerse the lamp in water.

* L = phase

= earthing

* N = neutral

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PLI-176 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PLI-176

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info