Bedienungsanleitung Profile PLI-800 (Seite 8 von 13) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

566827

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

LAMP WITH LED 6x1W + PIR EN - 1

LAMP WITH LED 10x1W + PIR

We thank you for the purchase of this Profile product.

Note: It is important that you read this manual carefully

before using the product and be sure to save this

manual for possible use later.

Note

Check if building regulations apply to your area

whereby you must have the lamp installed by an

accredited electrician. An electrician can give you

information about correct wiring. Never install the fitting

outside in rainy weather.

SWITCH OFF THE POWER BEFORE YOU INSTALL

THE LAMP.

Correct mounting

 With installation outside preferably choose a place

under a roof. Pay attention to the recommandations

in fig. 2

 To avoid malfunctions, do not aim the sensor to:

o Warmth sources (e.g. the sun, BBQ ...)

o Strong magnetic fields

o Reflecting surfaces (e.g. white walls,

swimming pools)

 The detection specifications can vary according to

altitude and place of assembly as well as

temperature oscillations.

 Before determinating the place of installation, be

aware that movement straight through the detection

area works more effectively than movement directly

to or away from the sensor. (fig. 4)

Correct installation

 Connect the lamp to a circuit with wall switch.

 Unscrew the bolts (fig 1.1) on the side to take the

holder (fig 1.2) from the fitting.

 Fix the holder to the wall with 3 screws.

 Fix the lamp back on the assembled holder and

adjust the light direction as you prefer.

 Remove the cover of the cable connection (fig 1.3).

 Untie the nut (fig 1.4) and the additional attachment

(fig 1.5) and pull the power supply wires through the

opening with the rubber packing.

 The lamp must be connected to mains voltage of

230V, max. fusing 16A.

 Connect the wires according to figure 3.

 Fix the cable connection cover, the nut and the

additional attachment.

 Always respect the instructions on the identification

label of the connected power cables.

 Other uses than described above can cause damage

to the product and increase the risk of short-circuit,

fire, electric shocks, etc.

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

 Setting the functions (fig 5)

1) Setting the light intensity (lux)

With the LUX Switch you adjust the working of the

sensor to match the intensity of the ambient light.

If the arrow is pointing to the sun the sensor responds

in both daylight and at night.

If the arrow is pointing to the moon the sensor will only

respond at night.

In between the sensor responds in half-light.

2) Setting the lighting time (TIME)

With this adjusting knob you can set the period of the

light staying on after switching on. You can set the

time from 10 sec. to 4 min.

3) Setting the sensitivity (SENS)

With this switch you can stipulate how sensitive the

sensor reacts to movement.

Safety instructions

 The importer accepts no responsibility for damage

claims with respect to objects or persons that result

from incorrect use or non-compliance with the safety

instructions. Any damage claims in such cases will

be declared null and void.

 The LED-lights are not replaceable.

 Always replace cracked or broken glass by glass

with the same properties as the original glass.

Technical information

 Working voltage: 220-240V~50Hz

 Maximum lamp power:

o PLI-800: 6x1W.

o PLI-801: 10x1W

 Maximum current strength: 10/16A.

 Dustproof and splashproof: IP44.

 Passive infrared sensor (PIR)

 Sensor angle: 180°

 Sensor range: 12 m.

 Lighting time: +/-10 sec. – 4 min.

Maintenance

 Only use a dry, soft cloth for cleaning the lamp.

 Never immerse the lamp in water.

 Maintenance and repairs may only be carried out by

technicians who are familiar with any applicable

regulations.

Guarantee conditions

The guarantee period for PLI-800/PLI-801 amounts to

2 years and commences on the date of purchase.

During the guarantee period ELTRA nv will repair any

defects attributable to material or production faults.

ELTRA NV may choose to either repair or replace a

defective appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PLI-800 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info