Bedienungsanleitung Profitech RTU5024 (Seite 6 von 11) (Englisch)

791935

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

-5-

For

example:

In NO the country code is 0047,or+47 .

The user cell phone number is 91234567 and has been assigned as the first user number, the simcard number

in the panel is 91234566 .

Problem

Relay

action

but

the

first

user

haven’t

received

the

SMS

Solution:

Please plus the country code while you setup the 91234567 as the first user number, means setup

004791234567 to instead of the 91234567 .

Problem

The

user

number

can

receive

the

Relay

action

message

from

the

RTU

5024,

but

the

RTU

5024

can

not

receive

the

commands

from

the

first

user

number.

Solution:

Please add country code to the simcard number in the RTU 5024. Means send sms commands to

004791234566 to instead of 91234566 .

Solution

When you use cell phone dial another one, what number it will be di splayed then you can set the

displayed number as dial numbers; when you use cell phone send SMS to another cell phone, what number it will

be displayed then you can set the displayed number as the first user number, just use the 00 to replace the “+”,

also, you can try the “+”.

2. All the settings are through SMS commands, please edit the below SMS commands in your cell

phone, then send to the RTU5024 Unit. The unit cannot support PIN Code Protected SIMCard.

3. You can program the GSM Gate Opener with SMS commands using your phone. It is safe to do

so because in addition to the fact that other people may not know the number of the SIM

inserted in it, we also use a Password that makes it impossible for anybody, who doesn't know it,

to access the system by chance.

4. The relay output will change the close or open status by every call in, please note it. Means the

first time call it, it will close the relay to switch on the lock, if the second call in is in the setting

time, then the unit will ignore the setting time, and open the relay, to switch off the lock or

machine.

5. Remember that commands must be CAPITAL Lock LETTERS .ItisPWDnotpwd,CAPnotCap

etc. Don't add spaces or any other character.

6. The pwd in the commands is means the password, when you use it, please in stand of it bythe

digital number; the capital letters PWD is the command letter, use PWD directly.

7. If you use this model for gate open, you only need to change the password andsetupthe

authorized numbers

8. In some GSM operators they use different SMS parameter; the units can’t return the SMS

confirmation is normally. It is not product problem. Also, you can try to add the country code

before the number, see the below settings:

9. Please write down the Authorized number list in a paper for review in further.

10. If you want to reset the RTU5024 to factory default, then please send pwd#RESET# （The unit will

reply to Reset Success! Please Reboot your Device ) or When the RTU5024 works normally, you

can always press the RESET key beside the SIMCard for several seconds until the RUN Led always

is ON.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profitech RTU5024 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profitech RTU5024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info