Bedienungsanleitung Proline TLW1000P (Seite 2 von 2) (Englisch)

632182

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 600 00088

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton

95 5.0

50*

1.70 2:05

Cotton** 60 5.0 45 0.89 2:45

Cotton** 60 2.5 33 0.68 2:10

Cotton 40 5.0 47 0.65 2:00

Cotton** 40 2.5 33 0.53 1:45

Cotton rapid 60 5.0 47 0.95 2:10

Synthetics 60 3.0 50* 0.90 2:05

Synthetics 40 3.0 40 0.50 1:50

Delicates 30 1.5 50 0.55 0:41

Quick wash 15' 30 3.0 30 0.15 0:15

Wool 40 1.0 55 0.55 0:45

Handwash 40 1.0 40 0.40 0:35

1. Load the machine, close the drum doors and check

that they are properly locked.

2. Add detergent and additives into the dispenser to

no more than the “MAX” level mark, as follows:

• Programmewithpreandmainwash

• Mainwashprogrammewithoutprewash

• Fabricsoftenersandconditioners

• Stainremoveragents

• Anti-scaleagents(ifnecessary)

3. Close the lid.

4. Turn the programme selector to the desired

programme and temperature. The lamp next to the

“Start/Pause” button flashes. If you do not start

the programe soon after having made your choice,

the washing machine will switch off automatically

after about a quarter of an hour. Switch on the

washing machine again by turning the programe

selector back to „Off/O“ and then to the desired

programe.

CONSUMPTION DATA

PREPARATION OF THE WASH CYCLE

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel (Reset) a running programme before

the end”.

Selecting or deselecting an option can be done at

any time during the programme. The option will be

applied as long as the corresponding programme

phase has not been executed yet.

“Spin speed reduction” button

• Reducesthepredeterminedautomaticmaximum

spin speed to treat your laundry more gently.

“Rinse hold” button

• Thelaundryremainsinthelastrinsewaterwithout

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• Thisoptionisparticularlyrecommendedforthe

“Synthetics” and “Delicates” programmes.

• It is useful if you want to postpone spinning to a later

time, or if you want to drain out only.

• If you select “Rinse Hold”, do not leave items to

soak for too long.

• As soon as the appliance stops in the rinse hold, the

“Rinse hold” lamp of the sequence indicator lights up

and the lamp next to the “Start/Pause” button

flashes.

Terminate the “Rinse hold” option:

• Pressthe“Start/Pause” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• Ifyoudonotwishtospintheclothes,turnthe

programme selector knob to the “Drain”

programme and press the “Start/Pause” button.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

PROGRAMME END

• The“Dooropen”indicatorlightsup.Afterabouta

quarter of an hour, the washing machine will switch

off completely to save energy.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the

interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme, any options and another

spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end. Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door can be

opened.

SELECT THE DESIRED OPTION(S)

FAILURE INDICATIONS

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer

to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference Programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.

Power consumption in off-mode 0.11 W / in left-on mode 0.11 W.

Proline TLW1000P Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Proline TLW1000P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info