Bedienungsanleitung Proosten LBC 500 SERIE (Seite 17 von 58) (Deutsch, Englisch, Holländisch, Französisch)

527015

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

E N

Input voltage protection

If a fault may occur on the input, the charger is protected by means of a fuse.

This fuse can be reached by removing the bottom plate of the charger. It is

located at the input side, where the power cord enters the charger. For

replacement, always use a fuse with the same value as the original one. See

specifications on page 54.

Input voltage monitoring

If the input voltage drops below 180VAC, the charger will protect itself and

pauses the charge process. The ‘power’ will light up red. The charge process

will be continued automatically if the input voltage has risen to 190VAC again.

Automatic voltage compensation

The charger automatically compensates for the voltage drop over the

connection cables. This compensation is optimized for the standard cable length

of 1 meters. To secure the correct working of the voltage compensation, it is

preferred not to change the length of the cables.

Charge time monitoring

All phases of the charge process are time monitored, but in particular the first

stage, the boost phase. If this phase takes longer than 14 hour, the charge

process will be stopped and the ‘ power’ LED will light up red. Most important

requisite of this feature is that this way is prevented that the charger keeps on

charging a broken battery. But with this feature it also can become clear that

the charger doesn’t fit the specific situation. For instance that the charge

current isn’t in the correct proportion to the battery capacity (the battery can

become damaged when the charge process takes too long) or due to the

presence of users there is insufficient current left for charging the battery.

Battery voltage protection

After switching on, the charger first monitors the battery voltage. If the charger

doesn’t detect a battery, the power led will light up red. If the charger measures

a battery voltage that is too low, so the battery is discharged too deeply, the

power led will light up red for 3 minutes as a warning. The charging process will

not start when the battery voltage is too high. Then the power led will also light

up red.

Temperature-compensated charging system

By connecting the optional temperature sensor T-Sense1, it is possible to adjust

charging process based on the battery temperature. Read more about this in

the relevant chapter.

Level of protection

The indication for the degree of protection contains the character ‘IP’

(International Protection) followed by two or three digits that stipulates the

conditions that it complies with.

The first digit refers to the class of protection for density, the second digit to

the fluid density and the last digit refers to the impact resistance. The LBC

500S can be assigned IP 205, which means:

2 = the charger is protected against solid particulate larger than 12mm.

0 = the charger is not protected against water/liquid etc.

5 = the charger can bear an impact force of 2.00 Joule (2Nm) max.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proosten LBC 500 SERIE Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Proosten LBC 500 SERIE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info