Bedienungsanleitung Proosten TBC 600 1-KANAALS - Software V1.3 (Seite 21 von 42) (Deutsch, Englisch, Holländisch)

527013

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

IN U S E

When turning on the charger the display will briefly indicate the adjusted charging setting

by way of a number and one or more led’s under ‘charge process’ will light up. At the

start of the charging process the TBC 600 first checks the battery voltage. If the battery

voltage is not correct then an error indicator will indicate this.

The charging process consists of 5 phases at most, depending on the charging program.

The length of the charging time depends on the battery quality, battery capacity, depth

of discharge and the current draw of any present users. Furthermore any faults could

delay the process. A short description of each charging phase:

1. Boost = T1

Every charging session begins with this phase, whether the battery is full or not. The

charging current is 100% and the voltage increases until the set voltage is reached. The

boost charge always takes at least 30 minutes. As such, even if a full battery is

connected this phase always takes 30 minutes. During this phase the red LED under

‘charging process’ lights.

2. Equalize = T2

The charging current is at most 100%, but because the battery is filling up the charging

current decreases. The charging voltage is at a maximum. The point at which the

following phase is entered depends on the charging program (based on time or on a

percentage of the charging current). However, this charge phase always has a duration

of maximum 4 hours, without any thermal stops which may occur. During this phase the

yellow LED under ‘charging process’ lights.

3. Compensate = T3

This is a special and extra phase for breaking down the sulphates which build up when

the battery is (deeply) discharged on a regular basis. The voltage can increase to 16Volt.

As such, this phase is only used in ‘stand alone’ applications (no users present during the

charging process). This phase isn’t suitable for most sealed, maintenance free batteries.

The compensation phase lasts at most 4 hours, plus any thermal stops which may occur.

During this phase the yellow LED under ‘charging process’ blinks.

4. Float = T4

The battery is full and is mainteananced with a lower, stable voltage of 13.5Volt or

13.8Volt, depending on the charge setting. During this phase, the charger can still supply

its maximum current without the charger going into the boost phase. Because of this the

TBC 600 is capable of supplying other devices when used ‘on board’. If the battery

voltage drops below 12.65 Volt for a longer period of time, the charger automatically

switches back to the boost phase (T1). During this phase the green LED under ‘charging

process’ lights.

5. Jogging = T5

If, during float charging, the charging current is less then 10% for more than 24 hours,

the charger switches over to jogging. This phase prevents a battery, which has been on

float charge for a long time, from becoming “lazy”. During this phase no charging current

is delivered. If the battery voltage drops below 12.65 Volt the charger

automatically switches back to the boost charge phase (T1). During this phase the green

LED under ‘charging process’ blinks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proosten TBC 600 1-KANAALS - Software V1.3 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info