Bedienungsanleitung Protool CSP132 (Seite 11 von 73) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490703

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

20 21

b) Check  the  spring  function  of  the  re-

tracting blade guard. If the retract ing 

blade guard and the spring do not op-

erate properly, have the machine serv-

iced  before  using.  The retracting blade

guard may operate sluggish due to dam-

aged parts, gummy deposits or build-up of

chips/sawdust.

c) Only  pull  back  the  retracting  blade 

guard manually for special cuts, such as 

“plunge and bevel cuts”. Pull back the 

retracting  blade  guard  with  the  pull-

back lever and release it as soon as the 

saw blade has penetrated the work. For

all other sawing jobs, the re tracting blade

guard must operate auto matically.

d) Do not place down the saw on a work 

bench  or  the  ground  without  the  re-

tracting blade guard covering the saw 

blade. An unprotected, coasting saw blade

will move the saw in the op posite direction

of the cut, cutting what ever is in its path.

Pay attention to the run-on period of the

saw.

e) Use the  matching  riving  knife  for  the 

saw blade being worked with. The riv-

ing knife must be wider than the thick ness

of the blade back, but thinner than the kerf

width of the saw blade.

f) Adjust  the  riving  knife  as  described 

in the operating instructions. Incor rect

width, position and alignment can be the

cause that the riving knife does not effec-

tively prevent kickback.

g) Always  use  the  riving  knife,  except 

when performing plunge cuts. After the

plunge cut, mount the riving knife again.

The riving knife interferes when performing

plunge cuts and can lead to kickback.

h) In order for the riving knife to be  ef-

fective, it  must be  located  in the  cut. 

For short cuts, the riving knife is ineffec tive

for the prevention of kickback.

i) Do not operate the saw with a bent riv-

ing  knife.  Even a minor malfunction can

lead to sluggish retraction of the re tracting

blade guard.

5.5  Emission levels

Levels determined in accordance with EN 60

745 are typically:

Sound pressure level L

= 102 dB (A)

Noise level L

= 113 dB (A)

Uncertainty K = 3 dB

    CAUTION

The  noise  created  during  work  may 

damage hearing. 

► Use hearing-protective aids!

Vibration emission value a

(vector sum for

three directions) and uncertainty K meas-

ured in accordance with EN 60 745: 3.1 m/s

Uncertainty K = 1.5 m/s

The emission values speci ed (vibration, noi-

se) were measured in accordance with the test

conditions stipulated in EN 60 745 and are

intended for machine comparisons. They are

also used for making preliminary estimates re-

garding vibration and noise loads during ope-

ration.

The emission values speci ed refer to the

main applications for which the power tool

is used. If the electric power tool is used for

other applications, with other tools or is not

maintained suf ciently prior to operation, ho-

wever, the vibration and noise load may be

higher when the tool is used.

Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speci ed time period. This

may signi cantly reduce the load during the

machine operating period.

6  Commissioning and 

Operation 

    WARNING

Risk of injury, if the tools are used with 

wrong supply power. 

The voltage specications on the rating plate

must correspond with the mains voltage.

Equipment marked with 230 V can also be con-

nected to 220 V / 240 V.

Check that the plug type is the same as the

socket type.

Adjustment of the riving knife 

   WARNING

Risk  of injury,  if the riving knife is not 

correctly adjusted. 

The riving knife [1-11] must always be used

for safety reasons. The riving knife prevents

the saw blade from becoming jammed when

making lengthwise cuts.

Loosen screw [1-12], adjust the riving knife

[1-11] and retighten the screw (see gure).

1-11

1-12

Check the function of the swinging guard [1-9].

Switching On/Off 

Switching On: 

Press the safety button [1-14].

Press the on-off switch [1-13] and hold depressed.

Note: The on-off switch cannot be locked on.

Switching Off: 

Release the on-off switch [1-13].

7  Adjustment 

    WARNING

Risk of electric injury. 

► Before any manipulation with the tool make

sure to unplug the mains socket outlet.

7.1 Electronic Motor Control

Soft start 

The electronically-controlled soft start en-

sures that the tool starts without jerking and

requires only a small starting current (weaker

fusesrequired).

Constant speed 

The motor speed is electronically stabilised.

This enables a constant cutting speed even

under a heavy load.

Overload protection 

In cases of extreme overload (rip cutting, use

of blunt saw blades) the power consumption

may considerably exceed the permissible rated

value. In this case an electronic overload de-

vice protects the motor from burning out. The

motor is hereby switched of by an “electronic

safety clutch” and re-starts as soon as the load

is removed.

Temperature protection 

Extreme overload in continuous operation

causes the motor to heat up. An electronic tem-

perature monitoring device is tted to prevent

overheating (motor burn-out). The electronic

safety device switches the motor off before the

motor is able to reach a critical temperature.

After a cooling period of approx. 3–5 minutes

the machine is once again ready for operation

and can run at full load. The cooling period can

be greatly reduced if the machine is running

(idling or recovery speed).

7.2  Cutting Depth Adjustment 

Release the locking lever [1-16].

Set the required depth on the cutting

depth scale [1-15].

Raise: smaller cutting depth

Lower: larger cutting depth

Re-tighten the clamping lever [1-16].

To achieve the best cutting results, the

saw blade should protrude from the

material by no more than 3 mm.

7.3  Cutting Angle Adjustment 

Release the cutting angle locking lever at [1-7]

and [1-18].

Set the cutting angle as required using the

scale [1-19]. (The scale is calibrated in 1° in-

crements).

Re-tighten the cutting angle locking lever at

[1-7] and [1-18].

   WARNING

The maximum cutting depth is reduced 

for bevel cuts. 

Protool CSP132 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info