Bedienungsanleitung Protool CSP85-45 (Seite 20 von 134) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490702

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

10 Maintenance

- The unit should be stored in a dry place

where it is protected against freezing.

WARNING

To verify that the protective insula-

tion remains intact, the machine must

be subjected to a technical safety test

afterwards. For this reason, this work

must be performed exclusively by a

professional electro-workshop.

- With each changing of the saw blade, re-

move deposited saw dust from the inside

of the protective guard.

- The ventilation slots on the motor casing

should be cleaned out from time to time.

After an operating period of approx. 200

hours, the following maintenance work

must be performed:

- Check the motor brushes and replace if

necessary. Clean the motor housing.

- Renew the grease ﬁ lling of the gear-

box.

11 Environmental

Protection/Disposal

Power tools, accessories and packaging

should be sorted for environmental-friendly

recycling.

Only for EC countries:

Do not dispose of power tools into

household waste!

According to the European Directive

2002/96/EC on waste electrical and elec-

tronic equipment and its incorporation into

national law, power tools that are no longer

suitable for use must be separately collect-

ed and sent for recovery in an environmen-

tal-friendly manner.

12 Warranty

For our tools, we give warranty for material

and production defects in accordance with

the locally applicable legal provisions, but

in any case for at least 12 months. Within

the EU member states, the warranty period

is 24 months (veriﬁ cation through invoice

or delivery note).

Damage caused by, in particular, natural

wear, overloading, incorrect handling, or

damage caused by the operator, or dam-

age caused through use of the equipment

contrary that speciﬁ ed in the Operating In-

structions, or damage which was known at

the time of purchase, is not covered by the

warranty. Furthermore, damage caused by

the use of non-original PROTOOL accesso-

ries and consumable material (e.g. sanding

pads) is also excluded.

Complaints can only be recognised if the

tool is returned while still assembled to the

supplier or an authorised PROTOOL Cus-

tomer Service workshop. Keep the Operat-

ing Instructions, Safety Instructions, Spare

Parts List and purchase receipt in a safe

place. Otherwise the respective, current

warranty condi tions of the manufacturer

shall apply.

Note

Due to continuous research and develop-

ment work, we reserve the right to make

changes to the technical content of this

documentation.

13 Declaration of

Conformity

We declare under our sole responsibility

that this product is in conformity with the

following standards or standardization doc-

uments:

EN 55 014-1, EN 55 014-2, EN 60 745-1,

EN 60 745-2-5, EN 61 000-3-2, EN 61 000-3-3

according to the provisions of the regula-

tions 98/37/EC, 2004/108/EC.

Manfred Kirchner

Research and development

Protool GmbH

Wertstr. 20

D-73240 Wendlingen

31.7.2008

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool CSP85-45 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info