Bedienungsanleitung Protool DRC 12-4 TEC LI (Seite 14 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

79301

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Declared total value of vibrations can be used for

preliminary setting of exposition.

Warning:

Emission of vibrations during real operating can

be different from declared total value of vibrations

depending on speciﬁ c real conditions.

To protect operating person shell be provide safety

measurement, that evaluate the exposition un-

der the real conditions (here are included all parts

of operating cycle, switch of mode and idle run

mode).

5 Commissioning

5.1 Changing the battery pack

Removing the battery pack

Press and hold the two buttons [2-1].

Slide the battery pack forwards to remove.

Inserting the battery pack

Slide the battery pack onto the retainer on the

underside of the handle shown in Fig. [2] until it

engages.

5.2 Charging the battery pack

► The battery pack is delivered partially charged.

Charge the battery pack completely before using

for the ﬁ rst time.

To charge the battery pack, slide all the way onto

the retainer [3-2] on the charger.

► To remove, slide the charged battery pack from

the charger in similar fashion.

The charger automatically detects the type of the

inserted battery (NiCd, NiMH or LiIon).

A microprocessor controls the charging process in

line with the charging state, temperature and volt-

age of the battery pack. If a warm NiMH battery

pack (> 37 °C) is inserted, the pack is charged with

a reduced charging current and will take longer to

charge.

The LED [3-1] on the charger indicates the respec-

tive operating status of the charger.

LED yellow – lit continuously

Charger is ready to use.

LED green – ﬂ ashing quickly

Battery pack is charged to maximum capacity.

LED green – ﬂ ashing slowly

Battery pack is charged with reduced current, LiIon

is charged to 80 %.

LED green – lit continuously

Battery pack is fully charged, conservation charg-

ing active.

LED red – lit continuously

Battery temperature is outside the permitted

range.

LED red – ﬂ ashing

General fault display, e.g. incomplete contact, short

circuit, battery pack faulty, etc..

5.3 Wall mounting

There are two elongated holes on the back of the

BC 3 for mounting the charger to a wall using two

screws (e.g. round head or ﬂ at head screw with

shank diameter of 5 mm).

Insert the two screws into the wall at a distance

of 96 mm from one another and leave the screw

heads protruding approx. 4 mm.

6 Machine settings

► Setting must be done only when the machine

is turned off and will be accepted only after

restarting it.

6.1 Changing the direction of rotation

The right/left switch [1-3] changes the direction

of rotation.

Move switch from right to left = clockwise rotation;

Move switch from left to right = anticlockwise rota-

tion.

6.2 Changing gear

► Always switch off the machine before changing

gear!

You can change gear using the gear switch [1-4].

6.3 Fastening

Move the switch [1-5] to the torque setting.

Setting on 1 = low torque

Setting on 12 = high torque

The machine switches off when the preset torque

is reached and an acoustic signal sounds. You must

release and press the ON/OFF switch [1-2] again

to start the machine.

Upon levels 1 – 12, a decreased number of rota-

tions can be set.

6.4 Drilling

The selector switch [1-5] is set to the drill symbol

marking

= maximum torque.

7 Tool holder, attachments

7.1 Chuck

The chuck is used for clamping drill and screw-

driver bits.

Attaching the chuck

► Before ﬁ rst use, the spindle [4-1] should be paint-

ed with a thin layer of multipurpose grease.

Attach the chuck to the drill spindle [4-1].

Pull the release ring [4-2] forwards.

Turn until the hexagon pinon the chuck engages in

the hexagon socket holder in the drill spindle.

Push the chuck all the way onto the drill spindle.

Release the ring [4-2].

Detaching the chuck

Pull the release ring [4-2] forwards.

Remove the chuck.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool DRC 12-4 TEC LI Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info