490654
16
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
16
LiIon battery packs, always use sand.
- Connecting the auto feed attachment and
drywall screwdriver results in a device,
which is subject to the safety regulations
and instruction for the drywall screw-
driver.
- Protect your eyes during use – pay due
care during overhead work!
- Use breathing protection, wear dust
mask!
4.3 Emission levels
Levels determined in accordance with
EN 60 745 are typically:
DWC 18-2500 DEC/18-4500 DEC
Sound pressure level L
PA
= 78 dB (A)
Noise level L
WA
= 89 dB (A)
Measuring uncertainty
allowance K = 3 dB
CAUTION
The noise produced during work may
damage your hearing.
Wear ear protection!
Overall vibration levels (vector sum for three
directions) measured in accordance with
EN 60 745:
DWC 18-2500 DEC
Vibration emission level
(3 directions) a
h
= 2.8 m/s
2
Uncertainty K = 1.5 m/s
2
DWC 18-4500 DEC
Vibration emission level
(3 directions) a
h
= 3.5 m/s
2
Uncertainty K = 1.5 m/s
2
The speci ed emissions values (vibration,
noise)
– are used to compare machines.
– They are also used for making preliminary
estimates regarding vibration and noise
loads during operation.
– They represent the primary applications
of the power tool.
Increase possible for other applications,
with other insertion tools or if not main-
tained adequately. Take note of idling and
downtimes of machine!
5 Commissioning
5.1 Changing the battery pack
Removing the battery pack
Press and hold the two buttons [2-2].
Slide the battery pack forwards to remove.
Inserting the battery pack
Slide the battery pack onto the retainer on
the underside of the handle shown in Fig. [3]
until it engages.
5.2 Charging the battery pack
The battery pack is delivered partially
charged. Charge the battery pack com-
pletely before using for the rst time.
To charge the battery pack, slide all the
way onto the retainer [2-1] on the charger.
To remove, slide the charged battery pack
from the charger in similar fashion.
The charger automatically detects the type
of the inserted battery (NiCd, NiMH or Li-
Ion).
A microprocessor controls the charging pro-
cess in line with the charging state, tem-
perature and voltage of the battery pack.
If a warm NiMH battery pack (> 37 °C) is
inserted, the pack is charged with a re-
duced charging current and will take longer
to charge.
The LED [3-2] on the charger indicates the
respective operating status of the charger.
LED yellow – lit continuously
Charger is ready to use.
LED green – ashing quickly
Battery pack is charged to maximum capa-
city.
LED green – ashing slowly
Battery pack is charged with reduced cur-
rent, LiIon is charged to 80 %.
LED green – lit continuously
Battery pack is fully charged, conservation
charging active.
LED red – lit continuously
Battery temperature is outside the permit-
ted range.
LED red – ashing
General fault display, e. g. incomplete con-
tact, short circuit, battery pack faulty, etc..
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Protool DWC 18-2500 DEC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info