Bedienungsanleitung Protool ISP 330 EB (Seite 28 von 182) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490698

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

opening on the guide bar [2-5] snaps onto the ten-

sion bolt [2-6]. Then put the chain sprocket cover

[2-1] on the clamping bolt [2-7] and tighten by

rotating the fastening wheel [2-2] clockwise. Make

sure the chain is tensioned correctly before tight-

ening. Check the chain for correct tension!

11.7 Replacing the chain sprocket

Remove the chain and the guide bar as described

above. Using a screwdriver, strip the snap safety

ring [8-1] from the spindle [8-4], and remove the

washer [8-2] and chain sprocket [8-3]. After re-

placement, put the washer and safety ring back

on.

11.8 Lubrication and cleaning

We recommend cleaning the machine regularly.

Remove dust, cuttings, resin and other impuri-

ties. Detergents that contain solvents can harm the

painted surfaces or plastic parts. If you use such

detergents, we recommend that you ﬁ rst test their

effect on a small hidden surface. During mainte-

nance or replacement of any part of the tool cutting

set, clean the inside of the cover by removing the

accumulated dust and cuttings, clean the guide

groove, as well as the lubrication and tension ports

of the chain’s guide bar. Do not clean the rotary

suction adaptor with your ﬁ ngers! The motor cov-

er’s ventilation ports must not be blocked!

11.9 Replacing the carbon brushes

WARNING

The saw must undergo safety inspection to main-

tain its protection category, and this work must

be done at an authorised facility licensed to per-

form such work. Before servicing the tool, always

unplug the cord from the socket!

Have an authorised service facility handle replace-

ment of the brushes, power cord, etc. If the ma-

chine is dropped, it must be checked by an au-

thorised service centre to prevent any electrical

or mechanical hazard.

After approximately 200 operating hours, the

brushes must be checked. The brushes are acces-

sible after removal of the hood. The brushes must

be replaced with new ones if they become shorter

than 5 mm.

The machine is equipped with self-detaching brush-

es that come off automatically once the minimum

length is reached. Use only original-equipment

brushes!

12 Environmental Protection /

Disposal

Power tools, accessories and packaging should be

sorted for environmental-friendly recycling.

Only for EC countries:

Do not dispose of power tools into house-

hold waste!

According to the European Directive 2002/96/EC

on waste electrical and electronic equipment and

its incorporation into national law, power tools that

are no longer suitable for use must be separately

collected and sent for recovery in an environmen-

tal-friendly manner.

REACh

REACh is a European Chemical Directive that came

into effect in 2007. As “downstream users” and

product manufacturers, we are aware of our duty to

provide our customers with information. We have set

up the following website to keep you updated with

all the latest news and provide you with information

on all the materials used in our existing products:

http://www.tts-protool.com/reach

13 Warranty

For our tools, we give warranty for material and

production defects in accordance with the locally

applicable legal provisions, but in any case for at

least 12 months. Within the EU member states, the

warranty period is 24 months (veriﬁ cation through

invoice or delivery note).

Damage caused by, in particular, natural wear, over-

loading, incorrect handling, or damage caused by

the operator, or damage caused through use of the

equipment contrary that speciﬁ ed in the Operat-

ing Instructions, or damage which was known at

the time of purchase, is not covered by the war-

ranty. Furthermore, damage caused by the use of

non-original PROTOOL accessories and consumable

material (e.g. sanding pads) is also excluded.

Complaints can only be recognised if the tool is

returned while still assembled to the supplier or an

authorised PROTOOL Customer Service workshop.

Keep the Operating Instructions, Safety Instruc-

tions, Spare Parts List and purchase receipt in a

safe place. Otherwise the respective, current war-

ranty conditions of the manufacturer shall apply.

Note

Due to continuous research and development work,

we reserve the right to make changes to the tech-

nical content of this documentation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool ISP 330 EB Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info