Bedienungsanleitung Protool JSP 120 (Seite 17 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490608

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

8.1 Free hand according to the

scribe mark

The triangular shape of the splinterguard [4-

3] shows the cutting line of the saw blade

and thus facilitates cutting to a scribe mark.

8.2 Plunge cutting without pilot

drilling

The base runner must be in the front position

for plunge cuts in timber materials (basic

setting, see Figure [1]).

Place saw on the front edge of the runner.

Set saw to maximum no. of strokes and pen-

dulum stroke setting 3 and start the plunge

cut into the workpiece (Figure [6]).

Damaged safety devices and components

must be repaired or replaced in a recognised

specialist workshop, unless otherwise indi-

cated in the operating manual.

To ensure constant air circulation, always

keep the cooling air openings in the motor

housing clean and free of blockages.

Use only original Protool accessories and

Protool consumable material intended for

this machine because these components are

designed specifically for the machine. Using

accessories and consumable material from

other suppliers will most likely affect the

quality of your working results and limit any

warranty claims. Machine wear or your own

personal workload may increase depending

on the application. Protect yourself and your

machine, and preserve your warranty claims

by always using original Protool accessories

and Protool consumable material!

10.1 Parallel guide

Use the parallel guide (order no. 764973) to

guide the jigsaw parallel to the workpiece

edge. The parallel guide can be fitted on both

sides of the base runner:

Slide clamping clip [7-1] onto the base run-

ner from the front.

Insert parallel guide [7-2] through the

clamping clip from the side to the desired po-

sition.

Tighten rotary knob [7-3].

10.2 Circle cutter

The circle cutter (order no. 764969) can be

used to produce circular cuts with a diameter

between 120 and 720 mm. The circle cutter

can be fitted on both sides of the base run-

ner:

Slide clamping clip [7-1] onto the base run-

ner from the front.

Insert circle cutter [7-4] through the clamp-

ing clip from the side to the desired position.

Tighten rotary knob [7-3].

Insert circle tip [7-5] in the rear bore hole of

the circle cutter.

10.3 Saw blades, other accessories

In order to saw different materials quickly

and cleanly, Protool offers saw blades for all

applications that are specially designed for

your Protool jigsaw.

Recommended number of strokes

(adjusting wheel setting)

Hard and soft wood, wood core ply-

wood, plywood, chip board

Wood fibre boards 4 - 6

Plastics 3 - 6

Ceramic, aluminium, NF metals 3 - 5

Steel 2 - 4

8 Working with the machine

WARNING

Risk of injury

Always secure the workpiece in such a

manner that it cannot move while being

machined.

9 Service and maintenance

WARNING

Risk of injury, electric shock

Always disconnect the mains plug from the

socket before performing maintenance

work on the machine!

All maintenance and repair work which re-

quires the motor housing to be opened

must only be carried out by an authorised

service workshop.

10 Accessories

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool JSP 120 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info