Bedienungsanleitung Protool MXP 1002 (Seite 12 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490692

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

6 Starting up and using the

machine

Check that the information on the manufacturing

label complies with the actual power supply volt-

age.

Check that the plug type is the same as the socket

type.

6.1 Tightening the stirrer

(see Fig. [2])

Screw in the stirrer [2-4] with endpiece M14x2

(wrench size 22) by turning it to the right in the

adapter ErgoFix [2-1] (wrench size 19) and use

the wrench to tighten it.

Fasten the ErgoFix adapter to the stirrer bar, then

insert the assembled stirrer into the slot of the

spindle. To set-up the working height see chap-

ter 6.5.

6.2 Switching the machine on and off

► Always hold the machine with both hands.

Pressing the switch [1-3] puts the machine into

operation and taking your hand away from the

switch stops the machine from working.

Using the switch button to control the speed

(acceleration function switch)

You can use the switch [1-3] to change the level

of the speed until it reaches the speed range that

is set by the speed controller.

Continuous operation

By pressing the switch [1-3] as far as it goes and

pressing the locking switch button [1-4] at the

same time, you can activate continuous operation.

Press and release the switch button [1-3] again to

switch off continuous operation.

6.3 Control electronics

Limiting the starting current

The electronically-controlled soft start ensures that

the machine starts up smoothly.

At the same time, this also prevents the materi-

als to be stirred from spurting out of the mixing

container. Thanks to the low starting current of the

machine, a 10 A fuse is sufﬁ cient.

Electronic speed preselection

You can use the speed controller [1-5] to set the

speed:

MXP 1000 EE F, MXP 1200 EE F

Level 1 360 Level 4 520

Level 2 410 Level 5 580

Level 3 470 Level 6 630

MXP 1002 EE F

1st speed 2nd speed

Level 1 360 Level 1 580

Level 2 410 Level 2 670

Level 3 470 Level 3 760

Level 4 520 Level 4 840

Level 5 580 Level 5 930

Level 6 630 Level 6 1010

The speed depends on the stirrer rod that is used

and on the material that you want to process.

Overload protection

An electronic overload protection protects the mo-

tor from damage if there is an extreme overload.

In this case, the motor remains at a standstill and

only starts up again once the load has been re-

moved. To restart the machine, you must switch

it on again.

Constant Electronic function

The Constant Electronic function maintains an al-

most constant speed and load; this ensures that

the material is stirred evenly.

Temperature-dependent overload protection

(VALID for the type MXP 1002 E EF and

MXP 1200 E EF)

To protect the machine against overheating if you

are using it for an extremely prolonged period,

switch the safety electronics to the cooling mode

as soon as the critical temperature is reached. You

cannot load the machine and it runs at a reduced

speed. Approx. 2 minutes after cooling, the ma-

chine is again ready for use and fully able to take

loads.

Protection against re-starting

Prevents the uncontrolled starting of the device

after current supply cut off. For re-starting, the de-

vice must be ﬁ rst switched off and again switched

on.

6.4 Speed selection switch

(VALID for the type MXP 1002 E EF)

You can use the speed selection switch [1-9] to

preselect two speed ranges:

1st speed 2nd speed

360 – 630 rpm 580 – 1010 rpm

The gears can be switched when the machine is

running down, however not under full load.

6.5 ErgoFix interface

Height setting

The working height of the machine can be indi-

vidually adjusted to achieve an upright working

position.

- Push the casing of the ErgoFix adapter [1-7] in

the direction of the machine to move it as far

as it goes [1-7] and hold it tight.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool MXP 1002 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info