Bedienungsanleitung Protool MXP 1202 (Seite 14 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490694

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

6.7 Mains connection

WARNING

There is a risk of accidents occurring if you

do not use the correct power supply.

The stirrer must only be operated with a single-

phase alternating current with a nominal voltage of

220–240 V/50–60 Hz. In the 2nd level, the machine

is protected against accidents caused by electrical

current in accordance with the standard EN 60 745-1

and it has built-in radio interference suppression in

accordance with the standard EN 55 014.

Before starting up the machine, check that the

speciﬁ cations on the type plate correspond to the

actual voltage of the power supply.

If required, you can extend the ﬂ exible power cable

as follows:

- Length 20 m, conductor cross-section

3×1.5 mm

- Length 50 m, conductor cross-section

3×2.5 mm

Only use extension cables that are suitable for

outside use and that are marked accordingly.

Operating with electric generator (EG) with

combustion motor drive

NOTE

► The manufacturer of the stirrer does not pro-

vide any guarantee for incorrect operation of

the stirrer with any EG.

The stirrer can be operated with an EG if the fol-

lowing conditions are met:

- The output voltage of the EG must always be

within the range of 230 VAC ±10%, the EG must

be equipped with Automatic Voltage Regula-

tion (AVR). The stirrer must not work correctly

without this regulation and may also become

damage.

- The power of the EG must be at least 2.5 times

greater than the connected load of the stir-

rer (i.e. 3 kW for MXP 1202 E EF, 3.75 kW for

MXP 1602 E EF)

- If you operate using an EG that does not have

sufﬁ cient power, the speed may ﬂ uctuate and

the power of the machine may decrease

6.8 Stationary use

The stirrer can be clamped into the MSP 57 PRO-

TOOL stirrer stands at the 57 mm collar [1-6].

6.9 Suction

CAUTION

Inhaling the dust may damage the respira-

tory tract.

► When working with dust, you must wear res-

piratory protection and connect the machine

to the suction attachment.

To extract dust from the mixing container, you can

connect it to the PROTOOL MXP suction attach-

ment.

7 Service and maintenance

CAUTION

Never use a machine that is damaged in any

way! (Damage also includes a ripped or worn

ﬂ exible switch protection or clamping ring

protection on the ErgoFix adapter).

► Have a damaged machine repaired in an au-

thorised PROTOOL workshop.

- To ensure safety against an accident caused by

electrical current and to retain the protection

level, this work must be carried out in an elec-

trical engineering workshop that is authorised

to carry out such repairs.

- The ventilation holes on the motor hood must

not be blocked.

- The machine automatically switches off if the

carbon brushes are worn. The machine must

be sent to the workshop for maintenance work

(see the supplied list).

- We recommend that you clean the machine reg-

ularly. Remove any dust, residual mixing mate-

rial and any other dirt. If you use solvent-based

cleaning agents, these may damage the painted

surfaces or the plastic parts. If you use these

cleaning agents, we recommend that you test

the effect of these agents on a small, concealed

area. The ventilation holes on the motor hood

must not be blocked.

- Commission an authorised workshop to

change brushes, the power cable etc.. If

the machine is knocked in any way, it is also

necessary to entrust an authorised workshop

in order to prevent any mechanical or electrical

danger arising.

- The packaged machine can be stored in a dry

place without heating as long as the inside tem-

perature does not fall below −5 °C. The unpack-

aged machine must only be stored in a dry,

enclosed space where the temperature does not

fall below +5 °C and where no extreme tem-

perature ﬂ uctuations occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool MXP 1202 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info