Bedienungsanleitung Protool pdc 12 4 tec li (Seite 16 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

389347

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

stage alters the screw-in depth by 0.1 mm.

Removing the screws

If you wish to unscrew a screw again, sleeve A or

B must be removed. Now set the screwdriver to

counterclockwise direction of rotation and unscrew

the screw.

7.5 Auxiliary handle

Fit the auxiliary handle right down onto the neck

of the gearbox so that the recess in the handle sits

on the protruding part of the gearbox.

Tighten the auxiliary handle by twisting the grip.

The auxiliary handle can be positioned through

30°.

The drilling depth can be set with the depth stop

[7-2].

7.6 Tool holder in the drill spindle

Bits can be inserted directly in the hexagon socket

holder on the drill spindle [4-1] to shorten and

reduce the weight of the machine.

8 Operation

Press the ON/OFF switch [1-2] to switch on the

machine.

The speed of the machine depends on how far the

ON/OFF switch is pressed in.

Release the ON/OFF switch [1-2] to stop the ma-

chine.

When the ON/OFF switch is released, the working

spindle (chuck) stops immediately.

Bit store [1-1]

The bit cartridge can be used to store bits and bit

holders. The magnetic holder can also be used for

screws and similar items.

Belt clip

Clamp for attaching to the belt [1-7; on the right/

left] enables the device to be attached to work

wear for a short-term.

Light and battery capacity indicator

The LED [1-9] is both a light and a battery capac-

ity indicator:

Press the light button [1-8].

1x Light on

► switches off automatically after 30 min.

2x Battery capacity indicator on

► switches off automatically after 10 sec.

3x LED off

The LED [1-9] on the lamp indicates the charging

status of the battery pack.

LED green – steady light: The Li-Ion

battery pack is charged to more than 60%.

LED green – slow ﬂ ash: The Li-Ion bat-

tery pack is charged to 60–30%.

LED green – rapid ﬂ ash: The Li-Ion bat-

tery pack is charged to 30–0%.

LED yellow – steady light: Battery pack

discharged. Please charge it!

LED red – steady light: The tempera-

ture value of the battery pack, electronic

compartment or the motor is higher than

the permissible limit.

LED red – ﬂ ashing: General fault indi-

cation, e.g., loose contact, short circuit,

defective battery pack, etc.

► The charge indicator works only with Li-Ion bat-

tery packs, not with NiCd or NiMH battery packs.

Acoustic warning

The acoustic warning is activated and the tool is

automatically switched off in the following instances:

peep

• The pre-set torque moment has been

achieved

• “Block protect”; static torque too high

• Machine overloaded

9 Service and maintenance

WARNING

Risk of injury, electric shock

- Always disconnect the battery pack from the

machine before any maintenance or care work!

- All maintenance and repair work which re-

quires the motor housing to be opened, must

only be carried out by an authorised service

workshop.

Observe the following care and maintenance in-

structions

- Keep the air slits on the machine and the charg-

er clean to ensure adequate cooling.

- Keep the contacts on the machine, charger and

battery pack clean.

Information on battery packs

- Where possible, store the battery pack in a cool,

dry place at a temperature between 5 °C and

25 °C.

- Protect the battery pack from moisture, water

and heat.

- Signiﬁ cantly shorter operating times after each

charge indicate that the battery pack is worn

and should be replaced with a new one.

- The LiIon battery pack is fully compatible with

the charger! Integrated electronics prevent

overloading and overheating during the charg-

ing process.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool pdc 12 4 tec li Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info