Bedienungsanleitung Protool PDP 20-4 DEC FF (Seite 14 von 87) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490605

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

DRP 18-4 DEC FF/ PDP 20-4 DEC FF

7.3 Selecting the operating mode

(only PDP 20-4 DEC FF)

Fastening / Drilling

Set the selector switch [1-5] to the

drill bit symbol.

When fastening

, always remember

to work in 1st gear and at low speeds.

Impact drilling

Set the selector switch [1-5] to the

hammer symbol.

The machine was designed for impact

drilling into tiles, masonry and stone.

8 Tool holder, attachments

8.1 Tool chuck CENTROTEC WH-CE

[3]

The tool chuck CENTROTEC WH-CE allows

you to change tools with a CENTROTEC

shank in a matter of seconds.

Always use a CENTROTEC tool chuck to

clamp CENTROTEC tools.

8.2 Chuck [4]

The drill chuck retains the drill or screwdriver

bit.

Before initial use:

apply a coat of multi-

purpose grease to the drill spindle.

8.3 Angle attachment [5]

The angle attachment (partly as an accesso-

ry) allows the user to drill and fasten at right

angles to the machine.

Before initial use:

apply a coat of multi-

purpose grease to the drill spindle and

gearbox extension.

8.4 Depth stop [6]

The depth stop (partly as an accessory) al-

lows the user to insert screws to a predefined

depth. You can set the dimension by which

the screw head protrudes above or is re-

cessed below the surface of the workpiece.

Depth setting

Turn the housing [6-1] to set

the desired fastening depth.

Each detent position chang-

es the fastening depth by 0.1

mm.

Sleeve A/B must be removed before a screw

can be unscrewed.

8.5 Tool holder in the drill spindle

[7]

Bits can be inserted directly in the hexagon

socket holder on the drill spindle to shorten

and reduce the weight of the machine.

9 Working with the machine

Please observe all mentioned safety in-

formations and the following rules

when working:

– Only use tools designed for the specified

maximum speed.

– Only sharp tools ensure efficient drilling

and prevent machine overload.

– Always use faultless, sharpened HSS drill

bits (HSS: High Speed Steel) when drilling

into metal.

– Do not cause the machine to seize through

overloading.

– Always switch off the machine before plac-

ing on the nut/screw.

–Caution: when inserting long screws, there

is a risk the bit may slip from the screw

head and cause injury.

– Machine vice: clamp the workpiece secure-

ly in a machine vice, for example, before

drilling to prevent the workpiece from

turning and causing accidents.

9.1 Bit store [1-1]

The magnetic bit store is designed for hold-

ing bits or bit holders.

WARNING

Risk of injury, electric shock

Always pull the plug out of the socket be-

fore performing any type of work on the

machine!

CAUTION

Tool has sharp edges and can cause cut-

ting injuries during a tool change.

Wear protective gloves!

CAUTION

Risk of injury

Clamp the tool centrally in the drill chuck!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool PDP 20-4 DEC FF Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info