Bedienungsanleitung Protool RGP 80-11 E (Seite 14 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490681

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

4 Control Elements

[1-1] Additional handle

[1-2] Switch lever

[1-3] Adjusting wheel

[1-4] Handle

[1-5] Knob

[1-6] Backstop bar

[1-7] Suction ﬂ ange

[1-8] Scale

[2-1] Bolt

[2-2] Retainer

[2-3] Washer

[2-4] Milling rings

[2-5] Tool carrier

[2-6] Guide surface

[2-7] Bolt

[2-8] Sliding part

[2-9] Slot

[2-10] Suction ﬂ ange

[2-11] Guide surface

Not all of the accessories illustrated or de-

scribed are included as standard delivery.

5 Notes on Safety

Prevention

DANGER

5.1 General Safety Instructions

- Before using the machine, carefully read

all safety instructions and the Operating

Instructions.

- Keep all of the attached documents and

pass on the documentation if the ma-

chine changes ownership.

5.2 Safety instructions for all

work activities

Safety warnings common for the

following works: grinding, surface

grinding, grinding with wire brush or

abrasive cutting:

a) This electromechanical tool is de-

signed to be used as a surface grinder

or a cutter with a cutter head. Read

all safety warnings, instructions, il-

lustrations and speciﬁ cations intend-

ed for this electromechanical tool.

Failing to meet all the below speciﬁ ed

instructions may lead to injury by electric

current, ﬁ re and/or serious injury.

b) This tool is not recommended for pol-

ishing or cutting. Execution of works

this tool is not designed for may create

a risk and cause injury of a person.

c) Do not use accessories which is not

explicitly designed and recommended

by the tool manufacturer. The fact that

the accessories an be attached to your tool

does not guarantee its safe operation.

d) Nominal rpm of accessories must be

at least equal to the maximum rpm,

stated on the tool. Accessories that op-

erate at higher rpm than are the nominal

rpm, may break and pull apart.

e) Outer diameter and thickness of your

accessories must be within the limits

of nominal range for your electrome-

chanical tool. Accessories of incorrect

dimensions cannot be either protected

enough or controlled properly.

f) Clamping dimensions of disks, ﬂ anges,

supporting plates or any other acces-

sories must be suitable for ﬁ xing to

the tool spindle. Accessories with clamp-

ing holes which do not correspond with the

mounting dimensions of electromechani-

cal tool will be unbalanced, may vibrate

excessively and cause loss of control.

g) Do not use damaged accessories.

Check the accessories prior to each

use: check the grinding wheels for

chips and cracks, check the sup-

porting plates for cracks, ripping

or excessive wear, check the wire

brushes for loose or cracked wires. If

accessories or tool fell down, check

the damage or mount undamaged

accessories. After the accessories

is checked and mounted, you and

also bystanders stand to be beyond

the level of rotating accessories and

leave the tools run free at highest

rpm for one minute. During this trial

time damaged accessories usually rips

apart or disintegrates.

h) Use personal protective means. De-

pending on use, use facial shield and

safety protective goggles. If appro-

priate, use dust mask, ear protec-

tors, gloves and work apron, capa-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool RGP 80-11 E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info