Bedienungsanleitung Protool RGP130 (Seite 18 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490679

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

7 Operation

7.1 Fastening the grinding wheel

Clean the ﬂ ange [2-1] and fastening nut

[2-3], as well as grinding wheel fasten-

ing areas [2-2]. Mount the ﬂ ange [2-1] by

ﬁ tting it externally on the spindle [2-5].

Mount grinding wheel [2-2]. Flange ﬁ tting

must ﬁ t the grinding wheel aperture. Press

in the spindle blocking plunger [1-6]. Press

in the blocking plunger only when device is

switched off and spindle not active. Turn the

spindle until blocking plunger ﬁ ts in. Screw

the fastening nut [2-3] by ﬁ tting it from the

grinding wheel [2-2] on the spindle [2-5].

Fasten the fastening nut [2-3] with key [2-4].

Before starting the device, make sure the

grinding wheel rotates smoothly.

► Use only grinding wheels recommended

by the manufacturer and designed ﬂ ange,

which are included in the package.

7.2 Positioning the handle

Sufficiently release the handle manual

screw [1-9] and tilt the handle [1-5] to set

the most suitable working position. Re-fas-

ten the manual screw [1-9].

7.3 Dust suction

Always work with connected suction device.

Insert the suction device pipe into the suc-

tion extension [1-3]. In order to increase

the efﬁ ciency, we recommend to use pipes

with 36 mm.

► Use solely suction devices with antistatic

pipe design.

7.4 Lifting the front brush

For wall lifting, it is possible to lift the lifting

segment [3-1] – see ﬁ gure [3].

7.5 Brush replacement

After wear and tear of the brush [4-1], it

must be replaced.

At ﬁ rst unscrew the screws with washers

[4-2], remove the brush from the cover [4-3]

with the springs [4-4]. Insert the springs

into the holes in the new brush and secure

the in the holes by turning them clockwise

– see ﬁ gure [4 a]. Deﬂ ecting the springs

from vertical direction does not constitute

a defect. Then remove the brush with ﬁ tted

springs, attach them on the cover [4-3] from

the front end and tilt them – see ﬁ gure [4 b].

Make sure that the springs in the cover ﬁ t

into the guiding holes and screw back the

screws with washers [4-2].

7.6 Grinding wheel

Depending on the application area, various

grinding wheels are available – see table

on page 20. Use solely wheels of PROTOOL

trademark, which guarantees the grinding

output of the machine.

8 Maintenance

- Wrapped electric tools can be stored in a

dry place without heating, with tempera-

tures not lower than –5 °C. Unwrapped

electric tools can only be stored in dry

places with temperatures not lower than

+5 °C, without sudden changes in the

temperature.

WARNING

Always remove the plug from wall

socket each time the machine main-

tenance is carried out!

- To ensure the airﬂ ow is sufﬁ cient, cooling

openings of the motor must be always

clean and free.

- The machine is equipped with special

self-disconnecting brushes. When the

brushes are worn, the power supply is

automatically disconnected, and the ma-

chine is stopped.

WARNING

To maintain the protection level, the

device must be checked in specialized

electro technical workshop, which is

authorized for such work and they

will inspect the safety of the device.

- Service – see enclosed sheet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool RGP130 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info