Bedienungsanleitung Protool WCP 32 (Seite 12 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490686

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

To protect operating person shell be provide safety

measurement, that evaluate the exposition under

the real conditions (here are included all parts of op-

erating cycle, switch of mode and idle run mode).

6 Tool clamping

WARNING

Always disconnect the plug from the elec-

tricity network socket before carrying out

any works on the tool.

6.1 Installation of diamond discs

Put the tool down with the rotation direction arrow

[1-5] up, and press the slide unblocking [1-4] to

open while preventing the slide to get released by

a slight counter pressure.

Open the shutter [1-11] on the quick-clamp nut

[1-10], and unscrew this counter clockwise. In ac-

cordance with required cut width install diamond

discs [1-13] and spacer rings [1-12] onto the ma-

chine spindle – see ﬁ gure [1c].

Tighten the quick-clamp nut [1-10] by hand, and

close the shutter [1-11].

CAUTION

Never install two discs without inserting at

least one spacer ring in between!

CAUTION

The arrow on the diamond disc must comply

with the arrow [1-5] on the tool cover!

Always install all four spacer rings, otherwise there

is a risk of injury and tool damage from loosened

discs.

► It is also possible to work with one disc only.

6.2 Slotting with four discs

It is possible to work with four diamond discs at

the same time only if you replace the spacer rings

[1-12] of the basic accessories of the machine with

the special, colour-coded set of nine rings supplied

as special accessories. Caution – rings from these

two sets cannot be combined.

Always install all spacer rings, otherwise there is a

risk of injury and tool damage from loosened discs.

Adapt the speed of cut progression as well as the

pressure to the higher load of the machine.

Attention: Optimum results of work and the high-

est safety level can only be guaranteed when using

original PROTOOL accessories.

6.3 Uninstallation of diamond discs

CAUTION

Diamond discs can be very hot after cutting.

Use gloves!

Hold the diamond rings ﬁ rmly, open the shutter

[1-11] on the quick-clamp nut [1-10], and loosen

the quick-clamp nut.

6.4 Adjusting the cutting depth

Rotate with the regulating wheel [1-3], until the

required cutting depth is indicated on the scale.

The values on the regulating wheel are for refer-

ence only; the depth changes with disc wear.

7 Dust exhaust

To provide for the exhaust function, connect the

hose of a PROTOOL class L, M or H exhauster (in

accordance with the type of processed material)

to the exhaust attachment [1-6].

Attention: Always work with the exhaust con-

nected. Use only exhausters with antistatic design

in order to prevent generation of static electricity

in dusty environments.

Note: check the exhauster function in case of ex-

cessive dust ejection during machine operation (see

the operating instructions for the exhauster).

8 Commissioning

Check if the data on the name plate comply with

the actual voltage of the power source.

Check if the plug connector type complies with the

socket type.

CAUTION

Use dust mask! Use hearing protection!

Operate the switch unblocking [1-2] to the ﬁ rst

stage (light pressure), and switch on the tool with

the switch [1-1]. Once the motor runs with con-

stant speed, press the switch unblocking [1-2] to

second stage, cut slowly into the material down to

the pre-set depth, and then push the machine in

the cutting direction.

Based on the sort of material being slotted, and on

the spacing of installed discs (width of slot), there

are remnants of material remaining between the

slots, and these are to be removed with the sup-

plied chisel. The narrower the slot you choose, the

more material gets crushed and is removed with

the exhaust. For this purpose, there is a spacer

ring set offered as special accessories to be used

for slotting with four discs – see clause 6.2. In this

way, a wider slot is produced without the need of

chiselling out remnants of material.

RECOMMENDATION

To achieve the required results of work fast-

er and with higher efﬁ ciency (especially in

hard materials), carry out the cuts in two

steps – pre-cut with smaller depth, and then

ﬁ nish the cut down to the required depth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool WCP 32 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info