Bedienungsanleitung Protool WCP50 (Seite 13 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490687

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

8.1 Smooth start-up

After switching on the machine, regulation elec-

tronic circuits provide for a smooth start-up up to

the operating speed without unnecessary kicks.

This decreases the wear of gears, and increases

machine lifetime.

8.2 Limitation of start-up current

The electronically controlled smooth start-up en-

sures that the machine starts up without a kick.

Due to limited start-up current of the machine, a

protection rating of 10 A is sufﬁ cient.

8.3 Overload protection

Is the tool overloaded, the oveload protection is

actuated, and the tool stops. When the load is

removed, the tool restarts automatically. Before

you continue in your work, you should let the tool

reach full speed.

8.4 Thermal overload protection

If you work with the tool for longer periods of

time under excessive load conditions, the motor is

switched off by the thermal protection that protects

the motor from overheating.

After having cooled down, i.e. after about 30 sec-

onds, the machine can be restarted again.

Causes of overheating: excessive pressure, de-

viation of tool from perpendicular position, bad

quality or excessive wear of disc.

9 Maintenance

- The unit should be stored in a dry place where

it is protected against freezing.

- The ventilation holes on the motor casing must

not get blocked up.

- The cable may only be replaced in a specialised

electrical workshop qualiﬁ ed to perform such

work.

After approx. 200 hours of use the following main-

tenance work must be performed:

- Check the length of the brushes. Brushes shorter

than 5 mm should be replaced.

- The machine turns itself off automatically when

the brushes are worn out. The machine must be

sent to a service centre for maintenance.

WARNING

To preserve the protection class the machine

must undergo a safety inspection; this must

be done in a specialised electrical workshop

qualiﬁ ed to perform such work.

- Service – see enclosed sheet.

10 Environmental Protection /

Disposal

Power tools, accessories and packaging should be

sorted for environmental-friendly recycling.

Only for EC countries:

Do not dispose of power tools into house-

hold waste!

According to the European Directive 2002/96/EC

on waste electrical and electronic equipment and

its incorporation into national law, power tools that

are no longer suitable for use must be separately

collected and sent for recovery in an environmen-

tal-friendly manner.

REACh

REACh is a European Chemical Directive that

came into effect in 2007. As “downstream users”

and product manufacturers, we are aware of our

duty to provide our customers with information.

We have set up the following website to keep you

updated with all the latest news and provide you

with information on all the materials used in our

existing products:

http://www.tts-protool.com/reach

11 Warranty

For our tools, we give warranty for material and

production defects in accordance with the locally

applicable legal provisions, but in any case for at

least 12 months. Within the EU member states, the

warranty period is 24 months (veriﬁ cation through

invoice or delivery note).

Damage caused by, in particular, natural wear,

overloading, incorrect handling, or damage caused

by the operator, or damage caused through use of

the equipment contrary that speciﬁ ed in the Oper-

ating Instructions, or damage which was known at

the time of purchase, is not covered by the war-

ranty. Furthermore, damage caused by the use of

non-original PROTOOL accessories and consumable

material (e.g. sanding pads) is also excluded.

Complaints can only be recognised if the tool is

returned while still assembled to the supplier or an

authorised PROTOOL Customer Service workshop.

Keep the Operating Instructions, Safety Instruc-

tions, Spare Parts List and purchase receipt in a

safe place. Otherwise the respective, current war-

ranty condi tions of the manufacturer shall apply.

Note

Due to continuous research and development work,

we reserve the right to make changes to the tech-

nical content of this documentation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool WCP50 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info