Bedienungsanleitung Proxxon FBS 240-E (Seite 7 von 11) (Englisch)

782202

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Motor:

Rotational speed 5,000-22,000/min

Voltage ~230 V, 50/60 Hz

Power consumption 100 W

Noise emission ≤ 70dB (A)

Vibration ≤ 2.5 m/s2

Please note that the sound and vibration measurements in

particular have been performed with Proxxon bits and cut-

ters. When using third-party brands we cannot guarantee

compliance with the statements given here!

Clamping and changing the bit

Important!

• Never work without safety glasses.

• Wear a protective mask if large amounts of dust or

harmful dusts accumulate.

• Never press the lock button while the device is oper-

ating.

• Depending on the collet size, bits and cutters may

have a shaft diameter of max. 3.2 mm.

• Insert the tools are far as possible when clamping. En-

sure that the shaft of the tool does not stand out more

than 30 mm from the collet. Excessively protruding

shafts can bend easily and contribute to poor concen-

tricity.

• Do not in any case use bits and cutters with an arbour

length of more than 55 mm!

• When using collets, always make sure that the collet

chuck and the utilised tool have the same shaft diam-

eter! The arbour of the tool must be seated firmly and

securely in the collet!

• Do not work with damaged, bent or worn bits and cut-

ters! Make sure the tools are in perfect condition.

Damaged or worn tools can break and cause injuries!

• When storing the bits and cutters, make sure they are

reliably protected from damage!

• A correct and consistent speed achieves a high grind-

ing performance, not excessive contact pressure!

• By tendency: Bits and cutters with smaller diameters

require higher speeds than those with a larger diam-

eter.

• Attention: You absolutely must observe the permissible

maximum speed of the bits and cutters! The tool can

break when the maximum permissible speed is ex-

ceeded. Flying parts can cause damage and severe in-

juries!

1. Slightly turn drill chuck 2(Fig. 2) and simultaneously

press lock button (1) until the latter engages.

2. Open chuck and change bit.

We recommend PROXXON collet chucks for optimal true

running.

Operating instructions

Using the machine

Attention:

Secure the work piece during work! In addition to en-

abling more pleasant and efficient working, it also re-

duces the risk of the workpiece flying about!

Please note: A work piece flying about is a risk for in-

juries! Use a vice or suitable clamping fixture to hold the

work piece!

It is imperative to avoid electric tool recoil!

1. To activate, operate switch 4 (Fig. 1) and set the right

speed for the work on rotational speed adjusting knob

1. Applicable in principle, tools with smaller diameters

must be operated at higher speeds, and tools with

greater diameters at lower speeds in order to achieve

optimal results.

2. When cutting or engraving, hold the machine as if it

were a pen (Fig. 3), being careful not to occlude the

vent slits.

3. For roughing down, grip the machine as if it were a

hammer (Fig. 4).

- 15 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FBS 240-E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info