Bedienungsanleitung Proxxon MICROMOT 50-E (Seite 6 von 7) (Englisch)

782204

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

- 7 -

Description of the machine

Note:

The set 38515 icludes additionally:

1 Power unit

1 set of tools, see page 8

1 flexible shaft, see also page 8

Legend

1. ON - OFF switch with speed control (MM 50/E only)

2. Retainer

3. Connecting cable

4. ON - OFF switch (MM 50 only)

5. Lock button

6. Clamping nut with collet

7. Housing cap

Functional Description

The PROXXON Rotary Tool Micromot 50 / Micromot 50/E

is the ideal tool for precise drilling, milling, grinding,

polishing, brushing. It can be used for cutting, for engraving

and to remove rust. For hobby electronics, model making,

precision mechanics, jewellery shops, opticians, arts, tool

and mould making. For marking tools and cameras. It can

be used on steel, non-ferrous metals, glass, plastic

materials, wood, minerals and ceramics. The drill spindle is

supported in a precision ball bearing which eliminates any

play. Excellent handling because of the pen-type grip. The

machine is reliably driven by a high torque motor. Type

50/E is fitted with an electronic speed regulator.

Technical data

Length: approx. 9" (220 mm)

Weight: approx. 1/2 lb (230 g)

Spindle collar: Ø 3/4" (20 mm)

Motor:

Speed (50): 20 000 rpm

Speed (50/E): 5000 to 20 000 rpm

Voltage: 12 to 18 V

Power draw: approx. 40 W

Noise level: ≤70 dB (A)

Operation

Clamping, changing tools

Warning:

Never press the locking pin (arrow Fig. 2) while the

machine is running.

– Turn the clamping nut 1 (Fig. 2) lightly while pressing the

lock button until the pin engages.

– Open the collet and change the bit.

Clamp all tools as short as possible. Shafts, which stick out

too far will easily bend causing the machine to vibrate.

Power supply:

Use only power units with a minimum power of 1 A. We

strongly recommend to use the PROXXON adaptors type

NG 2 (S/E) or the NG 5/E or the included power suppy

(only 38515).

Warning:

Do not use a power unit with external speed control in

combination with the Micromot 50/E !

1. Push the non-reversible plug into the power unit.

In case of overloading the PROXXON-power unit will

switch off automatically. Pull the mains plug out and let the

power unit cool down for some minutes.

Working with the machine

Warning:

Always wear goggles!

Do not use any broken grinding discs or bent shafts!

Wear a breathing mask when working under dusty

conditions!

2. Start the machine on switch 4 (Fig. 1) or set the correct

speed (50/E only) with the button 1

Note:

High performance is not achieved by high pressure but by

even speed!

Small tools = high speed

Big tools = low speed

3. For delicate work hold the tool like a pen (Fig. 3). Keep

the ventilation slots open.

4. For rough work hold the machine like a hammer

The electronic speed regulation works only with non-

stabilized power units (like for example all PROXXON-

power units). In connection with a battery the machine will

only run at high speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon MICROMOT 50-E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info