Bedienungsanleitung Proxxon PD 250-E (Seite 6 von 26) (Englisch)

782206

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

-6-

General safety instructions

Read and become familiar with this entireinstructions manual.

Learnthe tool`s applications, limitations and possible hazards.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of

checking to see that keys and adjusting wrenches areremoved

from tool beforeturning it on.

3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite

accidents.

4. DON'T USE IN DANGEROUS ENVIRONMENT.Don't use power

tools in damp or wet locations, or expose them to rain. Keep

work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should be kept safe

distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks, master swit-

ches, or by removing starter keys.

7. DON'T FORCE TOOL. It will do the job better and safer at the

rate for which it was designed.

8. USE RIGHT TOOL. Don't force tool or attachment to do ajob

for which it was not designed.

9. USE PROPER EXTENSION CORD. Make sureyour extension

cordisingood condition. When using an extension cord, be

suretouse one heavy enough to carry the current your product

will draw.Anundersized cordwill cause adropinline voltage

resulting in loss of power and overheating. Ta ble 1shows the

correct size to use depending on cordlength and nameplate

ampererating. If in doubt, use the next heavier gage. The

smaller the gage number,the heavier the cord.

Exception No. 1: The reference to the table and the table itself

may be omitted if astatement indicating the appropriate gage

and length is incorporated into the instruction.

Exception No. 2: The information regarding extension cords

need not be provided for apermanently connected tool.

10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves,

neckties, rings, bracelets, or other jewelry which may get

caught in moving parts. Non-slip footwear is recommended.

Wear protective hair covering to contain long hair.

Exception: The reference to gloves may be omitted from the

instructions for agrinder.

11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask

if cutting operation is dusty.Everyday eyeglasses only have

impact resistant lenses, they areNOT safety glasses.

12. SECURE WORK. Use clamps or avise to hold work when

practical. It's safer than using your hand and it frees both

hands to operate tool.

13. DON'T OVERREACH. Keep proper footing and balance at all

times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for

best and safest performance. Follow instructions for lubricating

and changing accessories.

15. DISCONNECT TOOLS beforeservicing; when changing acces-

sories, such as blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make

sureswitch is in offposition beforeplugging in.

17. USE RECOMMENDED ACCESSORIES. Consult the owner's

manual for recommended accessories. The use of improper

accessories may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury could occur if the tool

is tipped or if the cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Beforefurther use of the tool,

aguardorother part that is damaged should be carefully

checked to determine that it will operate properly and perform

its intended function check for alignment of moving parts, bin-

ding of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. Aguardorother

part that is damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into ablade or cutter against

the direction of rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER

OFF.Don't leave tool until it comes to acomplete stop.

Warning

Additional safety instructions for lathes:

For Your Own Safety Read Instruction Manual BeforeOperating Lathe

a) Wear eye protection.

b) Do not wear gloves, necktie, or loose clothing.

c) Tighten all locks beforeoperating.

d) Rotate workpiece by hand beforeapplying power.

e) Rough out workpiece beforeinstalling on faceplate.

f) Do not mount split workpiece or one containing knot.

g) Use lowest speed when starting new.

GROUNDING INSTRUCTIONS:

1. All grounded, cord-connected tools:

In the event of amalfunction or breakdown, grounding provides a

path of least resistance for electric current to reduce the risk of

electric shock. This tool is equipped with an electric cordhaving

an equipment-grounding conductor and agrounding plug.

The plug must be plugged into amatching outlet that is properly

installed and grounded in accordance with all local codes and

ordinances. Do not modify the plug provided -- if it will not fit the

outlet, have the proper outlet installed by aqualified electrician.

Improper connection of the equipment-grounding conductor can

result in arisk of electric shock. The conductor with insulation

having an outer surface that is green with or without yellow stripes

is the equipment-grounding conductor.Ifrepair or replacement of

the electric cordorplug is necessary,donot connect the equip-

ment-grounding conductor to alive terminal. Check with aquali-

fied electrician or service personnel if the grounding instructions

arenot completely understood, or if in doubt as to whether the

tool is properly grounded.

Use only 3-wireextension cords that have 3prong grounding plugs

and 3pole receptacles that accept the tool's plug.

Repair or replace damaged or worncordimmediately.

2. Grounded, cord-connected tools intended for use on asupply

circuit having anominal rating less than 150 volts:

This tool is intended for use on acircuit that has an outlet that

looks like the one illustrated in Sketch AinFigure30. The tool has

agrounding plug that looks like the plug illustrated in Sketch Ain

Figure30. Atemporary adapter,which looks like the adapter illust-

rated in Sketches Band C, may be used to connect this plug to a

2-pole receptacle as shown in Sketch Bifaproperly grounded

outlet is not available. The temporary adapter should be used only

until aproperly grounded outlet can be installed by aqualified

electrician. The green-colored rigid ear,lug, and the like, extending

from the adapter must be connected to apermanent ground such

as aproperly grounded outlet box.

Grounding methods





 



 

  

 

 







 

GROUNDING

ADAPTER

GROUNDING GROUNDING

MEANS

METAL SCREW

COVER OF GROUNDED

OUTLET BOX

<A> <B>

<C>

<D>

Fig. 30

Proxxon PD 250-E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info