Bedienungsanleitung Proxxon PD 250-E (Seite 13 von 26) (Englisch)

782206

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

-13-

4. Release all clamp screws (1) and drive the individual retaining

jaws (2) onto the work piece

If the work piece is not round and smooth at the support point, it

must first be turned round.

Lubricate the jaws and work piece regularly when turning.

5. Check that the work piece is positioned in the steady free of

play and retighten clamp screws (1).

Careand Maintenance

Cleaning

Caution!

Always disconnect the mains plug for all adjustment and mainten-

ance work! Risk of serious injuries or damage due to inadvertent

starting up of the device, or hazarddue to electric shock!

1. After use, thoroughly clean all chips from the machine using a

brush or handbrush. Do not use compressed air for cleaning.

2. Regularly lubricate or oil all moving parts, spindles and guides!

The outside of the housing can be cleaned with asoft, dry or

damp cloth. Do not use compressed air when cleaning.

It is possible to use mild soap or other suitable cleaning agent

here. Solvents or cleaning agents containing alcohol (e.g. petrol,

cleaning alcohol etc.) should be avoided, since these can attack

the plastic housing casings as well as wash offthe lubricants. To

avoid fireortoxic reaction, never use gasoline, naphtha, acetone,

lacquer thinner,orsimilar highly volatile solvents to clean the lathe.

Do not allow brake fluids, gasoline, or penetrating oils to come in

contact with the plastic parts. They contain chemicals that can

damage or destroy plastics.

Please observe:

All electrical or mechanical repairs should be done only by quali-

fied service technicians. When servicing use only PROXXON repla-

cement parts. Use of any other parts may create ahazardorcause

product damage.

Any attempt to repair or replace electrical parts on this lathe may

create ahazardunless repair is done by aqualified service techni-

cian. Repair service is available at your PROXXON service center.

Lubricating:

Lubricate or oil all parts according to lubrication diagram (Fig. 26).

A=oil /lubricate beforeuse

B=oil /lubricate once amonth

Adjusting the play of the guides (Fig. 27)

Turn switch OFF and always remove plug from power source befo-

re making any adjustments or repairs.

Note:

Even if the guides areregularly lubricated or oiled, it is unavoidable

that the guides will exhibit play after some time due to wear.

The proceduredescribed hereusing the example of the upper car-

riage is the same for all guides, thereforeitapplies analogously to

the other guides on your lathe. For that reason they will not be

treated separately here. Adjust the guides according to the motto:

As "tightly" as necessary,aseasy running as possible!

Please consider: If guides areset too closely,this causes higher

operating forces as well as increased wear!

1. Release and slightly unscrew the counter nuts 1ofthe adju-

sting screws 2for the upper carriage 3using an open-end

spanner 5.

2. Evenly turninthe adjusting screws 2with an Allen key 4until

the play is eliminated.

3. Retighten the counter nuts 1. In the process, hold the adjusting

screws 2inposition with the fixed spanner 5sothat they do

not misadjust again.

4. Turn over the machine and slightly unscrew the set screw 2

(Fig. 28).

5. Then check if the support can still be moved easily and if it runs

completely without play.

Adjusting the play of the handwheels (Fig. 29):

Just as for the guides, handwheel wear during operation cannot be

avoided which ensures that the backlash increases slowly but con-

sistently.Tominimise this again, please proceed as follows:

1. Hold on to the handwheel 1and release the cap nut 2.

2. Turn the handwheel slightly to the right.

3. Retighten the cap nut while still holding the handwheel.

Please consider hereaswell:

The complete elimination of the backlash and atoo "tight" adjust-

ment for the handwheels is unreasonable: If the handwheels are

set too closely,this causes higher operating forces as well as

increased wear hereaswell!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon PD 250-E Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info