Bedienungsanleitung Pulsar DIGISIGHT N770A (Seite 8 von 44) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

621720

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

USE OF THE ADDITIONAL WEAVER 7/8” RAIL

The riflescope is fitted out with an additional Weaver rail (8) located on the left

side of the body. With the help of this rail you can attach accessories like:

- accessory Pulsar - 940 IR Flashlight (940 nm);

- external power supply EPS3;

- video recorder CVR640 etc.

“Video out” jack (14) is designed to connect external recording devices and

to transmit video signal to monitors, TV sets etc.

Select a suitable video output standard - PAL or NTSC (refer to section

11 “Main Menu”).

Connect an external signal receiver to the “Video out” jack (14) and turn

on the scope.

However please note that higher sensitivity causes an increased noise

level in the picture, lower frame rate; image slows down, if the riflescope

is rapidly moved from one side to the other, the picture may be blurred

for a moment. Neither of these effects is a flaw of the unit. After the

SumLight™ Signal Processing Program is activated, light dots (pixels)

may appear in the field of view which is explained by operation

peculiarities of this function. This is not a defect either.

The riflescope has a number of modes to enhance image quality:

Autocontrast mode and Sum Light™ mode:

Mode “Autocontrast” allows rapid image contrast enhancement (button

(12), marked by icon).

Mode “Sum Light™” activates enhanced sensitivity algorithm for

operation in low light conditions or complete darkness (button (11), marked

by icon).

SumLight™

After the riflescope is switched on for the first time, the Sum Light™

activates automatically. The use of Sum Light™ substantially increases

sensitivity of the CCD array thus enabling observation in low light without

using the IR Illuminator.

When using the unit at a sufficient level of night illumination, the Sum Light™

function can be deactivated manually using the menu. Hereafter on activation

the DFA75 retains the function status before it was turned off.

The wireless remote control duplicates activation of the scope, IR Illuminator

and digital zoom.

“ON” button (23) – turning on/off the scope (keep pressed for two seconds

to turn on the scope);

“IR” button (24) - turning on/off the IR Illuminators, powers settings

selection;

“Zoom” button (25) – activation/deactivation of digital zoom.

The unit has three buttons:

To start using the wireless remote control you will need to activate it:

Turn on the scope and select menu option “RC activation”, marked by

icon in the data panel.

Press the “М” (5) button, a message “WAIT” will show up and countdown

will start within which you need to press any button of the RC.

If the activation is successful, a message “COMPLETE” will show up

next to icon. The RC is ready for use.

If the RC does not work, replace the battery. To do this, unscrew the

screws on the rear panel of the RC, remove the cover, pull out the old

battery and insert a new CR2032 battery.

Indication of hot functions

Switching IR Illuminator’s operating modes, brightness and contrast

adjustment, activation of the “Sumlight”, “Autocontrast” и “Zoom”

functions are shown as large pop-up icons in the upper part of the display.

Clock Set Up

Note: time settings will be kept in the memory of the scope for two

months after removal of batteries.

Selection/disable of video output signal

Press the the button “M” (5) and select icon using the “◄ ” (6)

and “►” (7) buttons.

Using the “◄ ” (6) and “►” (7) buttons the required video output signal –

PAL or NTSC.

To exit the main menu, keep the button “M” pressed for one second. Or

wait 10 seconds to exit automatically.

Press “М” and select icon in the menu.

Move the cursor with the navigation buttons to select time format

“24” or “AM/PM”.

Press “М” to proceed to hour setup. Set the hour with the navigation

buttons. You can keep the button pressed until the required value shows

up.

Press “М” to proceed to minute setup. Set the minute according to

instructions above.

To exit main menu, hold “M” pressed for one second. Or wait 10 seconds

to exit automatically.

◄

►

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pulsar DIGISIGHT N770A Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info