Bedienungsanleitung Pure Highway H240Di (Seite 16 von 20) (Englisch)

529192

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installation guide

Installation notes

Preparing to install Highway

Highway can be installed in any dashboard that has

an opening matching the dimensions shown in the

diagram below. The dashboard needs to be 4.75mm

- 5.56mm thick in order to be able to support

Highway.

Digital radio antenna setting

Highway features an SMB type digital radio

antenna connector and should be used with an

automotive antenna appropriate for your vehicle and

geographical area (e.g. band 3 for UK use).

An antenna is not supplied with the product in order

to allow an appropriate antenna to be used for your

speciﬁc vehicle needs.

If your chosen antenna operates at a different

voltage to the 12 Volts supplied by Highway, then an

in-line voltage regulator must be used to correct the

voltage to the level required by the antenna BEFORE

connecting the antenna to Highway. The antenna

power should then be set to 'ACTIVE' using the

previous steps (Highway is set to 'ACTIVE' from the

factory).

Under no circumstances should a separate power

supply at either 12 volts, or any other voltage, be

provided in-line with the antenna connection with the

antenna power set to either 'ACTIVE', or 'PASSIVE'

as this will present power to the product through the

centre of the antenna cable and will cause damage

to the product not covered by the warranty.

WARNING - Connecting an active antenna that

is not designed to operate at 12 Volts to the SMB

Digital Radio Antenna Connector on this product

could cause damage to the antenna, or the product

that is not covered by the warranty.

Installing a digital radio antenna

Highway is designed to work with an active digital

radio antenna. Before installing the Highway head

unit ensure that you have installed an appropriate

digital radio antenna in your vehicle. Refer to your

digital radio antenna installation guide for more

information.

Note: Always insert the mounting sleeve into the

dashboard before ﬁtting the head unit

Antenna power for Active Antennas:

As many automotive antennas have an amplifier

either built-in, or in-line with the cable connected

to the car stereo, this product provides power at

12 Volts along the centre of the digital antenna

connector (centre pin of SMB connector).

Most active automotive digital radio antennas work

on 12 Volts. However, some may be designed to

operate at other voltages, e.g. 5 Volts. The antenna

power output from the product is set to ‘Active’, i.e.

12 volts ON, from production (shown as ‘DAB ANT

ACTIVE’ in the system menu).

If your chosen antenna does not have an ampliﬁer

(i.e. it is ‘PASSIVE’), please set the antenna power

to ‘PASSIVE’ using the following steps before

connecting the antenna to Highway:

1. Press and hold the DISP button until ‘CLOCK’

appears on the top line of the display. This

shows that you have entered the system menu.

2. Press the button repeatedly until ‘DAB ANT’

appears on the top line of the display.

3. Turn the VOLUME dial until ’PASSIVE’ appears

on the second line of the display.

4. Press the DISP button once to confirm the

new antenna setting and return to the previous

screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pure Highway H240Di Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info