Bedienungsanleitung Qlima PGP113 (Seite 51 von 104) (Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

689391

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

90°).

c) Press down the variable control knob and hold for 30 seconds. While holding

down the variable control knob press the igniter button several times until

the pilot flame ignited. Release the variable control knob 10~20 seconds after

the ignition.

Note:

1. If a new tank has just been connected, please allow at least one minute or

more for the air in the gas pipeline to purge out through the pilot hole,

2. When lighting the pilot flame make sure that the variable control knob is

continuously depressed while pressing the igniter button. Variable control

knob can be released after the pilot flame lit for 10-20 seconds.

3. Pilot flame can be watched and checked from the peephole Iocated on the

base of burnerhead . If the pilot flame does not light or it goes out, repeat

step c.

d) Turn the variable controI knob to LO and Ieave it there for 5 minutes or more

before turning the knob to desired temperaturesetting.

e) If the burner flame goes out accidentally or it is blown out by wind, turn off

the heater and wait at Ieast 5 minutes or more to let the gas dissipate before

re-lighting to avoid possible gas explosion. Repeat steps b to d.

E FR GB IT N NL

Apagado Off Off Spenta Av Uit

Posición de

encendido

Position

d'allumage

Ignite posi-

tion

Posizione di

accensione

Tenn i

posisjon

Ontstekings

positie

Capacidad

baja

Capacité

faible

Low capa-

city

Bassa capa-

cità

Lav kapa-

sitet

Laag ver-

mogen

Alta capaci-

dad

Capacité

élevée

High capa-

city

Alta capa-

cità

Høy kapa-

sitet

Hoog ver-

mogen

Table 1

TO TURN OFF THE HEATER

a) Turn the variable control knob to PILOT position.

b) Press and turn the variable control knob to OFF position.

c) Turn off the valve on the gas cylinder and disconnect the cylinder.

WARNINGS

• The whole gas system. hose, regulator, pilot and burner should be inspected

for Ieak before use. But at least once a month and each time the gas cylinder

is changed. Check the hose assembly for sign of extreme abrasion, cuts or

wears. Suspected areas should be Ieak tested. If the hose Ieaks, it must be

replaced with a new one that conforms to IocaI standard codes. ). If it shows

signs of cracking, splitting or other deterioration it shall be exchanged for

new hose of the same length and of the equivalent quality.

• Make sure the ventilation opening of the cylinder enclosure, controI com-

partment, burner and circulation air passageways of the heater are free and

clear of debris. If debris, spider or insect nests are found, clean the holes with

heavyduty pipe cleaner or compressed air.

• Always keep a dry chemical fire extinguisher readily available.

• For safety, always allow a 5-minute complete shut off period before re-light-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Qlima PGP113 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info