Bedienungsanleitung Quadra-Fire 2100 Millennium (Seite 10 von 32) (Englisch)

815518

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

10 02/237039-802G

Figure 10.1

HIGH

MED

LOW

Burn Rate

Air Control

Start-Up

Air Control

It is very important to reload your appliance while

enough lively hot coals remain in order to provide the

amount of heat needed to dry and rekindle the next load

of wood. It is best to open the Burn Rate Air and Start-

Up Air Controls before reloading. This livens up the coal

bed and reduces excessive emissions (opacity/smoke).

Open door slowly so that ash or smoke does not exit

appliance through opening. You should also break up

any large chunks and distribute the coals so that the

new wood is laid on hot coals.

Air quality is important to all of us, and if we choose to use

wood to heat our homes we should do so responsibly.

To do this we need to learn to burn our appliances in

the cleanest way possible. Doing this will allow us to

continue using our wood appliances for many years to

come.

2. Medium low burn setting:

- Burn Rate Air Control spring handle up to high position

for 5 minutes.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

until the knob stops.

- At that point move the Burn Rate Air Control spring

handle to 1/8”-1/2” from the low setting.

3. Medium high burn setting:

- Burn Rate Air Control spring handle up to high position.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

until the knob stops.

- At that point move the Burn Rate Air Control spring

handle to 1/2” – high.

4. High burn setting:

- Burn Rate Air Control spring handle up to high position

- Also activate ACC timer system knob pushed back to

the “HI” position.

Surface Thermometer is a Valuable Guide to Operation

A surface thermometer tells you when to adjust the air

control, and when to refuel, Figure 10.1.

For example, when the thermometer registers at least 450°F

(230°C) on the stove top after start-up you know the stove

is hot enough and it may be time to adjust the air control

if a su󰀩cient ember bed has also been established. Note

that the stove will warm up much sooner than the chimney,

though; a warm chimney is the key to easy, e󰀨ective stove

operation. When thermometer readings drop below 350°F.

(175°C) it’s time to adjust the air control for a higher burn

rate or to reload the stove. A temperature reading over

650°F. (340°C) is a sign to reduce the air supply to slow the

burn rate.

Use the following temperature ranges as a guide:

• Readings in the 350°-500°F. (175°-260°C) range indicate

low to medium heat output.

• 500°-600°F. (260°-315°C) readings indicate medium

heat output.

• Readings of 600°-650°F. (315-340°C) indicate high

heat output. Operating your wood stove continuously at

stove top temperatures higher than 650° F (340°C) may

damage your wood stove.

NOTE: The above information is provided as a guideline

only. Altitude and other circumstances may require

control adjustments to achieve the desired burn rates.

NOTE: Operate appliance on High Burn 45 minutes a

day to help keep ue/chimney clean.

NOTE: If using the optional blower, for burn rate settings

1-3, the blower shall be o󰀨 for the rst 30 minutes and

then be operated in the high position at 30 minutes. For

high burn setting, blower may continue to be on full after

the loading of the fuel.

D. Burn Rates and Operating E󰀩ciency

For maximum operating e󰀩ciency

This wood appliance has a manufacturer-set minimum

low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this

wood appliance in a manner inconsistent with operating

instructions in this manual.

• Burn dry, well-seasoned wood.

Burn Rates

1. Low burn setting:

- Burn Rate Air Control spring handle up to high position

for 5 minutes.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

until the knob stops (Figure 10.1).

- At that point close the Burn Rate Air Control by moving

the spring handle to the low setting.

Surface

Thermometer



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire 2100 Millennium Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire 2100 Millennium

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info