Bedienungsanleitung Quadra-Fire 3100 Millennium (Seite 10 von 32) (Englisch)

815517

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

10 02/237033-351J

It is very important to reload your appliance while

enough lively hot coals remain in order to provide the

amountofheatneededtodryandrekindlethenextload

ofwood.ItisbesttoopentheBurnRateAirandStart-

Up Air Controls before reloading. This livens up the coal

bedandreducesexcessiveemissions(opacity/smoke).

Opendoorslowly so that ash orsmokedoesnotexit

appliancethroughopening.Youshouldalsobreakup

any large chunks and distribute the coals so that the

new wood is laid on hot coals.

Air quality is important to all of us, and if we choose to use

wood to heat our homes we should do so responsibly.

To do this we need to learn to burn our appliances in

the cleanest way possible. Doing this will allow us to

continue using our wood appliances for many years to

come.

2. Medium low burn setting:

- BurnRateAirControlspringhandleuptohighposition

for 5 minutes.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

untiltheknobstops.

- Atthatpoint move theBurnRateAirControlspring

handleto1/8”-1/2”fromthelowsetting.

3. Medium high burn setting:

- BurnRateAirControlspringhandleuptohighposition.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

untiltheknobstops.

- Atthatpoint move theBurnRateAirControlspring

handleto1/2”–high.

4. High burn setting:

- BurnRateAirControlspringhandleuptohighposition

- AlsoactivateACCtimersystemknobpushedbackto

the“HI”position.

Surface Thermometer is a Valuable Guide to Operation

A surface thermometer tells you when to adjust the air

control, and when to refuel, Figure 10.1.

For example, when the thermometer registers at least 450°F

(230°C)onthestovetopafterstart-upyouknowthestove

is hot enough and it may be time to adjust the air control

ifasufcientember bed has also been established. Note

that the stove will warm up much sooner than the chimney,

though;awarmchimneyisthekeytoeasy,effectivestove

operation.Whenthermometerreadingsdropbelow350°F.

(175°C) it’s time to adjust the air control for a higher burn

rate or to reload the stove. A temperature reading over

650°F. (340°C) is a sign to reduce the air supply to slow the

burn rate.

Usethefollowingtemperaturerangesasaguide:

• Readings in the 350°-500°F. (175°-260°C) range indicate

low to medium heat output.

• 500°-600°F. (260°-315°C) readings indicate medium

heat output.

• Readings of 600°-650°F. (315-340°C) indicate high

heatoutput.Operatingyourwoodstovecontinuouslyat

stove top temperatures higher than 650° F (340°C) may

damage your wood stove.

NOTE: The above information is provided as a guideline

only. Altitude and other circumstances may require

control adjustments to achieve the desired burn rates.

NOTE: Operate appliance on High Burn 45 minutes a

daytohelpkeepue/chimneyclean.

NOTE: If using the optional blower, for burn rate settings

1-3,theblower shall be offfor the rst30minutesand

then be operated in the high position at 30 minutes. For

high burn setting, blower may continue to be on full after

the loading of the fuel.

D. Burn Rates and Operating Efciency

For maximum operating efciency

This wood appliance has a manufacturer-set minimum

low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this

wood appliance in a manner inconsistent with operating

instructions in this manual.

• Burndry,well-seasonedwood.

Burn Rates

1. Low burn setting:

- BurnRateAirControlspringhandleuptohighposition

for 5 minutes.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

untiltheknobstops(Figure 10.1).

- AtthatpointclosetheBurnRateAirControlbymoving

the spring handle to the low setting.

Figure 10.1

HIGH

MED

LOW

Burn Rate

Air Control

Start-Up

Air Control

Surface

Thermometer 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire 3100 Millennium Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire 3100 Millennium

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info